background image

Operation

75

FalconV User Manual - Standard Scanning - OPEX Corporation

Wait for the slot to become solidly lit.

Inject the item(s) one at a time into the slot.

When finished, press the Rescan Feeder button again.

The slot will no longer be illuminated and feeding will resume at the auto-

feeder.

To use the Rescan Feeder with Multi-Feed detection during the paused 
state:

When the Rescan Feeder slot is flashing, press and hold the Rescan 
Feeder button until the Rescan Feeder slot begins to flash rapidly.

Inject the item(s) one at a time into the slot.

When finished, press the Rescan Feeder button again.

The slot will no longer be illuminated and feeding will resume at the auto-

feeder.

About the pre-feeder mechanism

The pre-feeder mechanism consists of left and right pre-feeder wheels located 
directly to the right of the feed belt and the MFD override LED and the MFD 
override button.

The pre-feeder mechanism can only be activated via the MFD override button 
when the machine is in a jammed or paused state. In the event of a jam, the 
Pre-Feeder LED will flash green at a 0.5 second interval; alerting the operator 
that it may be selected for use to re-feed any rejected or jam sorted sheets. If 
the operator activates the Pre-Feeder, the LED will be solidly lit green and the 
Pre-Feeder arms will raise to allow the item(s) to be placed under them. 
Selecting the Pre-Feeder again will cause the Pre-Feeder LED to shut off, the 

Pre-Feed MFD Override button 

Pre-Feed MFD Override LED 

Summary of Contents for FalconV



































































































































Reviews: