background image

V-Zero 

Monophonic Guitar Synthesizer 

www.opfxs.com

 

 

User Manual 

 

V-ZERO is a monophonic guitar synth based upon principles of subtractive synthesis. When a note is played the pedal 
senses the pitch of the note and drives the on board oscillators. The generated signals can be mixed and processed in 
various way by filtering and applying modulations.  

Detailed description of every control 

Oscillators: 

 

OSC1 Waveform (4P rotary switch): Sine, Saw, Square, Triangle 

 

OSC2 Waveform (4P rotary switch): Sine, Saw, PWM, Triangle 

 

OSC1 Octave (6P rotary switch): 6 octaves range 

 

OSC2 Octave (6P rotary switch): 6 octaves range 

 

OSC 1-2 mix (pot): mixes OSC1 and OSC2 

 

OSC 1 tune (pot): fine tunes OSC1 pitch 

Mix and output: 

 

Mix (pot) : mixes dry guitar signal with synthesizer signal 

 

Volume (pot): output level 

 

Output jack: a standard TS jack plug can be used or TRS for splitting the output. TIP of the jack carries synth + 
dry guitar signal, RING carries dry signal. TIP signal is affected by MIX and VOLUME controls  and can be 
bypassed while RING signal is not affected by MIX or VOLUME and can't be bypassed. Split function permits to 
drive two different amplifiers or routing the signal to different external devices. 

Modulation: 

 

LFO rate (pot): speed of the LFO 

 

LFO depth (pot): depth of the LFO 

 

VCA mod (tactile switch with blinking LED): 

o

 

short press: LFO modulates VCA 

o

 

long press: instrument envelope modulates VCA 

 

LPF mod (tactile switch with blinking LED) : 

o

 

short press: LFO modulates LPF 

o

 

long press: instrument envelope modulates LPF 

o

 

pressing CONTROL and LPF MOD together turns on or off “LPF frequency modulation from OSC2” 

 

Pitch mod (tactile switch with blinking LED): 

o

 

short press: LFO modulates pitch of both OSC1 and OSC2 (Control LED = green) 

o

 

long press: applies pitch portamento, portamento time can be set with LFO rate pot 

o

 

pressing CONTROL and PITCH MOD together turns on or off LOW TRACKING FUNCTION 

 

LFO Wave (tactile switch with LED) : when off the LFO wave is a sine wave, when on the LFO wave is a square 
wave 

o

 

pressing CONTROL and LFO Wave together switches between LFO groups (SINE/SQUARE or 
SQUARE/SAW) 

 

Summary of Contents for V-Zero

Page 1: ...is affected by MIX and VOLUME controls and can be bypassed while RING signal is not affected by MIX or VOLUME and can t be bypassed Split function permits to drive two different amplifiers or routing the signal to different external devices Modulation LFO rate pot speed of the LFO LFO depth pot depth of the LFO VCA mod tactile switch with blinking LED o short press LFO modulates VCA o long press i...

Page 2: ...sonance is off Other infos V ZERO works with any pick up position but with some instruments open strings E tracks better with bridge pick ups V Zero works with any type of guitar 6 strings 7 strings etc Different tunings of the instrument is also possible CONTROL LED HOLD MODE LFO PITCH mod button VCA mod button LPF mod button short press long press short press long press short press long press of...

Page 3: ...atus V Zero memorizes the status of LPF frequency modulation and will recall it at next power on By default it s turned off LFO groups When CONTROL and LFO Wave are pressed at same time the LFO selection switches between Sine Square and Square Sawtooth This simply means that by pushing LFO wave button it will either switch between Sine LED off Square LED on or Square LED off Sawtooth LED on Pay at...

Page 4: ...ance between low and high notes tracking TIPS Avoid playing close to the amplifier with pickups facing the speakers this can make tracking of V Zero less effective always play with pickups off axis with respect to speakers or 180 from them Tech Specs The pedal works with standard 9V DC PSU negative center Current consumption min 260 mA all LEDs OFF Current consumption max 290mA all LEDs ON Input I...

Reviews: