background image

NLV

-

 

3101

-

 

HD

 

Specifications Manual

 
 
 
 
 

27 

 

9.5.

 

Cable Strength 

There shall be no sign of malfunction after the following cable strength test. 

Cable Strength Test:

 Affix the scanner to an immovable object and pull it using a force of 24.5 N 

(2.5 kgf static loading) for 1 second. Repeat this 20 times continuously. 

 
 

9.6.

 

Cable Bending Strength 

There shall be no sign of malfunction after the following cable bending test. 

Cable Bending Test: 

Add a load of 4.9 N (500 gf) to a cable and bend it at an angle of 60° to both 

right and left. Repeat this 1000 times continuously. 

 

 

 

Figure 21: Cable Bending 

 

 
 

9.7.

 

Vibration Strength (without packing) 

There shall be no sign of malfunction after the following vibration test.

  

Vibration test:

 Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity 

of 19.6m/s

2

 (2.0 G) for 30 minutes (60 minutes per cycle) in the non-operating state. Repeat this in 

each X, Y and Z direction.  

 
 

9.8.

 

Vibration Strength (in individual packing) 

There shall be no sign of malfunction after the following vibration test. 

Vibration test: 

Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity 

of 19.6 m/s

2

 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state. Repeat this 

in each X, Y and Z direction.  

 

 

Summary of Contents for NLV-3101-HD














































Reviews: