background image

 

 

UL/IEC Statement 

 
This equipment has been tested and found to comply with the limits for 
medical devices in IEC 60601-1:1994.

  These limits are designed to provide 

reasonable  protection  against  harmful  interference  in  a  typical  medical 
installation. 
This equipment generates uses and can radiate radio frequency energy and, 
if  not  installed  and  used  in  accordance  with  the  instructions,  may  cause 
harmful  interference  to  other  devices  in  the  vicinity.    However,  there  is  no 
guarantee  that  interference  will  not  occur  in  a  particular  installation.    If  this 
equipment  does  cause  harmful  interference  to  other  devices,  which  can  be 
determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures: 
 

 

Reorient or relocate the receiving device. 

 

Increase the separation between the equipment. 

 

Connect the equipment into an outlet on a circuit  different from that 
to which the other device(s) are connected. 

 

Consult the manufacturer or field service technician for help. 

 

 

Type of protection against electric shock: Class I equipment 

 

Degree of protection against electric shock: Not classified - no applied 
parts 

 

Classification according to the degree of protection against ingress of 
water  as  detailed  in  the  current  edition  of  IEC 529:  IPX0,  ordinary 
equipment 

 

This  equipment  is  not  suitable  for  use  in  the  presence  of  flammable 
anesthetics or oxygen 

 

Mode of operation: continuous operation 

 
 
 

Certification of Eye Safety 

 

This  laser  product  is  inside  implemented  by  using  1300/1550nm  optical 
module,  manufactured  by  Opticis  Co.,  Ltd.,  which  are  all  certified  by 
IEC/EN60825-1  referred  in  Accession  Number  07-1334-0217  as  classified  in 
Laser Class1. 
 

 

 
 
 
 
1-9 Regulatory Statements 

©  2015 Opticis Co., Ltd.  All Rights Reserved 
Revision 1.4.  2, Jan, 2015 
 

 
 
 
 
 
 
 

Opticis Locations 

 

Headquarters 

 

Opticis Co., Ltd. 
# 16Fl, Kins Tower  
8 Sungnam-daero, 331 beon-gil, 
Bundang-gu, 
Seongnam-si, Gyunggi-do, 463-844 
South Korea  
Te l: +82 (31) 719-8033 
Fax: +82 (31) 719-8032 

www.opticis.com

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

For order support, please contact your Distributor or Reseller. 

 

For technical support, check with the Opticis web site www.opticis.com or 
contact 

techsupp@opticis.com

 

 
 
 

Summary of Contents for M1-201DA-TR







Reviews: