background image

TWL-L-

R User’s Manual 

Page  iii of iii  

 

Optilab, LLC

 

 

600 E. Camelback Road, Phoenix, AZ  85012 
Phone:  (602) 343-1496, Fax:  (602) 343-1489, Email:  sales@oequest.com 
 

 

Table of Contents                                                                                                                                                                    

 

1.

 

General Information ___________________________________________________ 1

 

1.1

 

Introduction  ______________________________________________________________ 1

 

1.2

 

Product Overview __________________________________________________________ 1

 

1.3

 

Features __________________________________________________________________ 1

 

1.4

 

User Safety  _______________________________________________________________ 2

 

2.

 

Operation ____________________________________________________________ 2

 

2.1

 

Introduction  ______________________________________________________________ 2

 

2.2

 

Initial Inspection ___________________________________________________________ 2

 

2.3

 

Controls __________________________________________________________________ 3

 

2.4

 

Operation Instructions ______________________________________________________ 4

 

2.5

 

Software Interface and Control  ______________________________________________ 4

 

2.5.1

 

Serial communication  ___________________________________________________________ 4

 

2.5.2

 

Operating Guide for GUI _________________________________________________________ 5

 

2.5.3

 

Installation ____________________________________________________________________ 5

 

2.5.4

 

Operation _____________________________________________________________________ 6

 

2.6

 

LCD Front Panel Controls  __________________________________________________ 7

 

3.

 

Troubleshooting_______________________________________________________ 9

 

4.

 

Technical Specifications ________________________________________________ 9

 

5.

 

Mechanical Specifications  _____________________________________________ 10

 

6.

 

Service and Support___________________________________________________ 11

 

6.1

 

Warranty ________________________________________________________________ 11

 

6.2

 

Service and Calibration ____________________________________________________ 11

 

6.3

 

Care of Fiber-optic Connectors______________________________________________ 12

 

Summary of Contents for TWL-L-R Series
















Reviews: