background image

 

 

 

X6R/V3R-TP

 

26 / 27 

rev. 2.4 

Warranty and Liability 

Summary of Warranty 

OPTOCORE  X6R/V3R-TP  device  is  warranted  against  defects  in  material  and  workmanship  for  60  months  (5 
years) from the date of purchase. This warranty does not include mechanical damages caused by misuse. This 
warranty  covers  the  original  registered  purchaser  only  and  is  not  transferable.  This  warranty  does  not  apply  to 
devices which have been purchased in used condition or demonstrator equipment. 

OPTOCORE  will,  at  its  discretion,  repair  or  replace  a  defective  product,  providing  that  the  defect  has  occurred 
under normal operating conditions. 

This  warranty  does  not  cover  damage  from  acts  of  God,  accident,  abuse,  neglect,  contamination,  unauthorised 
modification,  misuse,  or  operation  outside  of  the  environmental  specifications  for  the  product,  improper  site 
preparation  or  maintenance,  or  abnormal  conditions  of  handling.  This  would  include  over-voltage  failures,  and 
conditions  outside of  the products specified  ratings, problems  with  customer-supplied  software  or  interfacing,  or 
normal wear and tear of mechanical components. OPTOCORE will acknowledge the evaluation of warranty after 
inspection. 

Not  covered  by  this  warranty  are  defects  arising  from  electromagnetic  or  electrical  interferences,  deficiency, 
excess, or surge of electrical supply, air conditioning, or humidity. This also includes repairs made necessary by 
dirt, abrasion, moisture, rust, corrosion, or similar conditions. 

Devices on which the Serial Number has been removed or defaced are not eligible for warranty service. 

OPTOCORE  devices  contain  no  user-serviceable  components:  refer  to  qualified  service  personnel  for  repair  or 
upgrade.  The  warranty  will  be  void  if  you  tamper  with  internal  components.  Please  address  any  questions  or 
inquiries to OPTOCORE or your distributor/dealer. 

For a full warranty conditions refer to the Warranty Card attached to every Optocore device with a first shipment. 

How to Obtain Warranty Service 

When  discovering  a  problem  with  an  OPTOCORE  device,  you  should  contact  either  Optocore  directly  or  a 
dealer/distributor  to  determine  and  confirm  a  hardware  fault.  If  it  is  a  software  issue  the  hardware  must  not  be 
returned to OPTOCORE, OPTOCORE will issue a support ticket in this case.  

If  hardware  service  is  required  within  the  warranty  period,  take  the  equipment,  along  with  warranty  card,  to  the 
nearest  authorised  OPTOCORE  dealer/distributor.  The  dealer/distributor  will  make  sure  that  the  device  is 
serviced according to the terms of warranty by OPTOCORE or an authorised service centre. 

If the equipment needs to be returned directly to OPTOCORE, first contact support@optocore.com. 

OPTOCORE requires the serial number of the equipment intended for return, as well as a short description of the 
problem.  If  possible,  you  should  also  provide  us  a  phone  number  where  you  can  be  reached  during  regular 
working  hours.  To  return  a  defective  product,  please  contact  your  distributor  /  dealer.  Our  web  site: 
http://www.optocore.com/ provides a complete list of Optocore distributors / dealers. 

Make  sure  the  equipment  being  returned  is  packed  carefully  to  protect  it  from  damage  during  shipment. 
OPTOCORE requires that shipments are pre-paid and insured – unless specifically authorized in advance.  

We strongly advise not to use simple flight-cases without rack-in-rack mounting. 

Declaration of Liability 

Optocore accepts no liability for damage caused to other devices through operation of the X6R/V3R-TP device. 

Optocore is not liable for any damage caused by shipping accidents, misuse, abuse, operation with incorrect AC 
voltage, operation with faulty peripheral equipment, or improper or careless installation of the device. 

Neither OPTOCORE nor anyone involved in the production of the equipment shall be liable for 
any indirect, special, disciplinary, consequential, or incidental damages arising out of the use 
or  inability  to  use  this  equipment  even  if  OPTOCORE  has  been  advised  of  the  possibility  of 
such damages. In no event shall the liability of OPTOCORE exceed the purchase price of any 
defective equipment.

 

Optocore accepts no claims for compensation whatsoever (e.g. cancellation of events). 

 

Summary of Contents for V3R




























Reviews: