Oracle Audio Delphi Mk VI Owner'S Manual Download

Page: 3 / 22

Oracle Audio Technologies

TABLE OF CONTENTS

Unpack your Delphi MK VI .................................................................. 4

Assemble the sub-chassis ................................................................... 6

Install the tone arm and phono cartridge.............................................. 6

Precisely align the phono cartridge ...................................................... 8

Assemble and level the plinth .............................................................. 9

Install the MVSS plungers.................................................................. 10

Prepare and install the suspension modules...................................... 11

Calibrate the suspension ................................................................... 12

Filling the MVSS reservoirs with the Silicone fluid ............................. 13

Install the drive belt ............................................................................ 14

Calibrating the Micro Vibration Stabiliser System .............................. 16

Attach the phono lead ........................................................................ 17

Connect the power supply ................................................................. 17

Adjust the 33 / 45 speed .................................................................... 17

Attach the ground lead....................................................................... 18

Install and calibrate the hinges........................................................... 18

The record clamp and tapered washer .............................................. 19

Level your Delphi MK VI .................................................................... 20

Maintenance ...................................................................................... 21

Specifications..................................................................................... 21

Warranty registration card.................................................................. 22

Summary of Contents for Delphi Mk VI























Search results

Summary of Contents for Delphi Mk VI

Reviews:

Related manuals for Delphi Mk VI

Brands by name

Popular brands

Oracle Audio Delphi Mk VI, Owner'S Manual

Search results

Summary of Contents for Delphi Mk VI

Reviews:

Related manuals for Delphi Mk VI

Brands by name

Popular brands