Oracle Netra SPARC S7-2 Service Manual Download

Page: 33 / 258

Interpreting LEDs

Rear Panel LEDs

No.

LED

Description

Power supply status LEDs

(note AC supply shown):
■ OK LED (top, green)

Indicates that power supply is functional (on) or with fault (off).

■ Service Required LED

(amber)

On indicates that service for the power supply is required. POST and Oracle ILOM are two

diagnostic tools that can detect a fault or failure resulting in this indication.

The Oracle ILOM

show faulty

command provides details about any faults that cause this

indicator to light.

NET 0 to NET 3 Status

LEDs

Link and Activity LED

(green)

Indicates these conditions:

■

On or blinking

– A link is established.

■

Off

– No link is established.

NET MGT status LEDs:
■ Link and Activity LED

(green)

Indicates these conditions:

■

– A link is established.

■

Blinking

– There is activity on the link.

■

Off

– No link is established.

■ Speed LED (amber/

green)

Indicates these conditions:

■

Green

– The link is operating as a 10000-Mbps connection.

■

Amber

– The link is operating as a Gigabit connection (1000-Mbps).

■

Off

– The link is operating as a 100-Mbps connection or there is no link.

Chassis status LEDs:

Detecting and Managing Faults

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Service Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands