Defining Cleaning Cartridge Usage Count Warning Thresholds
11-4
StorageTek SL3000 Library Guide
7.
When the unload notification appears, unload the CAP (follow
on page 10-2 starting with step 2).
Defining Cleaning Cartridge Usage Count Warning Thresholds
The warning threshold should be lower than the cartridge's recommended maximum
usage to allow time to replace the cartridge (see the drive manufacturers'
documentation for recommended usage).
When you import a cleaning cartridge into the library, the library controller sets the
usage count to zero. To display the current usage count, see
1.
In SLC, select
Tools > System Detail
. Select the
Library
in the device tree.
2.
Select
Auto Clean
, and then the
Warning Threshold
tab.
3.
Select the index number of the cleaning cartridge type to configure.
4.
Enter the new warning threshold for the cartridge type. To disable the warning, set
the threshold to 0.
5.
Click
Apply
.
Configuring the Barcode Format for FC-SCSI Hosts
The barcode format specifies which part of a cartridge barcode the library passes to
FC-SCSI hosts.
1.
In SLC, select
Tools > Configuration
.
2.
From the drop-down list, select the presentation format to use for each partition:
■
all
— passes all eight barcode characters to the host.
■
left6
(default) — passes only the six VOLID characters to the host. It does not
pass the domain and type characters, which are the two characters on the right
of the barcode.
3.
Click
Apply
.
Viewing Cartridge Information
1.
In SLC, select
Tools > Reports
.
2.
Expand the
Status Summary
folder in the navigation tree.
3.
Select the
Cartridge Table
.
See Also
■
"Viewing Cleaning Cartridge Status"
■
"Viewing Library and Device Reports with the Reports Utility"
Note:
The warning threshold for all cleaning cartridges of that type
will be modified.
Summary of Contents for StorageTek SL3000
