background image

OPERATING INSTRUCTIONS

Orascoptic

®

 Telescopes

1

Table of Contents

1.   

Before Using – Adjust Your Telescopes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.  

Side Shields – Titanium Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3. 

Side Shields – Designer Sports Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4. 

Using Your Orascoptic Telescopes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5. 

Cleaning Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.   

Telescope Prescription Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

7.   

Cleaning and Refurbishing Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

8.   

Laser Loupe Safety Instructions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Getting started 

With Orascoptic

®

 Telescopes

Although your new telescopes have been fully tested and adjusted by our 
factory technicians, they may need to be initially customized to your facial 
anatomy. Please read the following guide to learn how to adjust and care for 
your new telescopes — now and in the future. If you need help, call a trained 
technician. See the back of this manual for contact information.

Summary of Contents for Telescopes












Reviews: