2-20
INSTALLATION
ORBAN MODEL 9300
2.
Temporarily set the external AGC mode to “No.”
Navigate to
S
ETUP
>
N
EXT
>
N
EXT
>
E
XT
AGC
and set
E
XT
AGC
to
N
O
.
If you are using a external AGC like the Orban 6300, you should restore this set-
ting to
Y
ES
after the setup procedure is complete.
3.
Adjust Input selector.
A)
Navigate to
S
ETUP
>
IO
C
ALIB
>
I
NPUT
>
A
NLG
I
N
C
ALIB
.
B)
Set the
I
NPUT
to
A
NALOG
.
The 9300 will automatically switch to its analog input if signal lock is un-
available at its AES3 input.
4.
Adjust Analog Input Reference Level.
[
9dBu to +13dBu (VU), or –2 to +20dBu (PPM)] in 0.5 dB steps
[Skip this step if you will not be using the analog input.]
The reference level VU and PPM (Peak) settings track each other with an offset
of 7 dB. This compensates for the typical indications with program material of a
VU meter versus the higher indications on a PPM. (See
This step sets the center of the 9300’s gain reduction range to the level to which
your studio operators peak their program material on the studio meters. This as-
sures that the 9300’s processing presets will operate in their preferred range.
You may adjust this level with a standard reference/line-up level tone from your
studio or with program material.
Note that in this step, you are calibrating to the normal indication of the studio
meters; this is quite different from the actual peak level.
If you know the reference VU or PPM level that will be presented to the 9300, set
the reference level to this level, but please verify it with the steps shown directly
below.
A)
Press the
R
ECALL
button.
B)
Turn the knob until
GEN
PURPOSE
MEDIUM
appears in the lower line of the
display.
C)
Press the
R
ECALL
N
EXT
button.
D)
Navigate to
S
ETUP
>
IO
C
ALIB
>
I
NPUT
>
A
NLG
I
N
C
ALIB
>
AI
R
EF
(VU
or
PPM,
de-
pending on which metering system you use
)
.
E)
Calibrate using Tone.
[Skip to step (F) if you are using Program material to calibrate the 9300 to
your standard studio level.]
a)
Verify
E
XT
AGC
is set to
N
O
.
Summary of Contents for OPTIMOD-AM 9300
