background image

 

 

SPECIFICATIONS

 

Power Requirement  AC 220 - 240V / 50Hz 

Lighting Load 

Up to 2000W Incandescent or 
up to 1500W Fluorescent 

Detection Angle 

Up to 360

°

 at 25

°

C at 5m 

Height 

Detection Distance 

Up to 5m radius at 25

°

C at 2.2m 

height 
Up to 7m radius at 25

°

C at 5m 

height 

Mounting Height 

Recommended 2.2 - 5m (7.2 - 
16.4 Ft) Ceiling Mount   

Sensor Operation 

Auto 

Time Adjustment 

5 sec. - 40 min. ( 5, 10, 20, 40, 
80, 160 seconds and 5, 10, 20, 
40 minutes) 

Lux Adjustment 

Approx. 30 - 200 Lux /test mode 

Warm Up Time 

About 1 min 

Protection Class 

Class II 

Protection Degree 

IP20 

Safety 

CE 

Specifications are subject to change without notice. 

A501111848R02 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
New Zealand 
PO Box 100-707 
N.S.M.C 
Auckland 
Phone +64 (0)9 917 4000 
Phone 0800 232 633 
info@cdb.co.nz 
 
Australia 
PO Box 574 
South Morang 
Victoria, 3752 
Phone +61 (0)3 9336 4423 
Phone 1300 465 324 
info@cdbgoldair.com.au   
 

WARRANTY 

 
Your  product  is  warranted  against  faults  and 
manufacture  when  used  in  normal  domestic 
use for a period of one year.   
   
We  undertake  to  replace  this  product  at  no 
charge  if  found  to  be  defective  due  to  a 
manufacturing  fault  during  the  warranty 
period.  This  warranty  excludes  damage 
caused by misuse, neglect, shipping accident, 
incorrect  installation,  or  work  carried  out  by 
anyone  other  than  a  qualified  electrical 
service technician. 
If  your  product  fails  to  operate  satisfactorily, 
please  return  it  to  the  retailer  from  whom  it 
was  purchased  to  obtain  a  repair  or 
replacement  product.  You  will  need  to 
produce  satisfactory  evidence  of  date  of 
purchase.  If  the  product  is  to  be  replaced 
(cannot  be  repaired)  then  that  replacement 
will  be  of  the  same  or  similar  product  or 
accessory  excluding  packaging,  instruction 
card etc.   
In  New  Zealand  product  is  covered  by  the 
Consumers  Guarantee  Act  (1993).    In 
accordance  with  the  act  consumers  are 
advised  that:  The  manufacturer  does  not 
undertake  that  repair  facilities  and  parts  are 
necessarily available for this product. 

In Australia, our goods come with guarantees 
that cannot  be  excluded  under  the  Australian 
Consumer  Law.  You  are  entitled  to  a 
replacement or refund for a major failure and 
compensation  for  any  other  reasonably 
foreseeable  loss  or  damage.  You  are  also 
entitled  to  have  the  goods  repaired  or 
replaced  if  the  goods  fail  to  be  of  acceptable 
quality  and  the  failure  does  not  amount  to  a 
major failure.   

 

 

Summary of Contents for OSLPIR360W

Page 1: ... it is raining DO isolate the power supply during installation or maintenance DO ensure that the power supply circuit is protected by a 16 amp circuit breaker or suitable equivalent fuse The unit cannot be installed on the wall FIGURE 1 FIGURE 1 IMPORTANT Installation must be performed by skilled technicians who are informed about the standards and technical requirements of the appliance and its p...

Page 2: ...e wire nuts provided 3 Study the following figure for wiring information The power cords of LS and N marks are to be connected to the lighting fixture FIGURE 4 Warning Incorrect wiring could damage the sensor or connected load and also may cause electrical harm FIGURE 4 4 In order to install the sensor to the ceiling drill a diameter of 68mm round hole on the ceiling Wedge the main body into the r...

Page 3: ... 40 second 8 20 minute 4 80 second 9 40 minute LUX ADJUSTMENT The LUX adjustment determines at what light level the light will start operating when you set the sensor to the AUTO MODE FIGURE 8 Provisionally turn the LUX Control Knob to the edge clockwise at the moon dusk position FIGURE 8 In this provisional setting mode the Motion Sensor remains inactive during daylight At dusk when you find it i...

Page 4: ...anufacturing fault during the warranty period This warranty excludes damage caused by misuse neglect shipping accident incorrect installation or work carried out by anyone other than a qualified electrical service technician If your product fails to operate satisfactorily please return it to the retailer from whom it was purchased to obtain a repair or replacement product You will need to produce ...

Reviews: