background image

Prepare Orbital Systems Shower Head

1

RSK 188 25 12

1.

Measure and mark placement of Wallbox UNI Push.

1900mm - 2300mm

2.

Follow instructions provided in installation box for the
Wallbox UNI Push. Installation should be performed
according to local regulations. Make sure that the
support sleeve is inserted into the pipe and that the pipe
is fully inserted, and past the o-ring, into the Wallbox UNI
Push.

Wallbox UNI Push with
external support
sleeve

Wallbox UNI Push with
integrated support
sleeve

x4

Pan head stainless steel screw

Prepare 3rd Party Shower Head

At this stage, consider the necessary preparations for
installing the 3rd Party Shower Head, according to local
regulations.

Requirements for installing 3rd Party Diverters, Shower
Heads and Hand Showers (applies to installation with Orbital
Shower):

• When using a 3rd Party Diverter, Shower Head or Hand

Shower, it is recommended to choose products with low
counter pressure in order to optimise the Orbital Shower
performance. Should the combined counter pressure from
the Diverter and Shower Head / Hand Shower exceed 1
bar at 10 L/min, it will affect the lifespan of the Filter
Capsule negatively. A combined counter pressure
exceeding 1,5 bar at 10 L/min is not recommended.

• Any installed Shower Heads / Hand Showers should allow

for a water flow of min. 9 L/min.

• It is recommended to install Diverters designed for wall-

integration.

Pipes and Connections

2

RSK 188 07 62

Provided by Customer:

• PEX Hose with Conduit Ø25 mm
• Power Cable with Conduit Ø16 mm
• Anchors

1.

CAUTION

The Orbital Shower Core shall be
connected to the top inlet.

CAUTION

The Shower Head shall be connected to
the bottom inlet.

Ø25mm

Page 22 of 33

Summary of Contents for OAS Standart R3


































Reviews: