background image

blade speed (rpm) 

3075 

3075 

3075 

3075 

Over all width (mm) 

815 

815 

950 

950 

 

 

 

CHECK

 

LIST 

 

INSTRUCTIONS TO THE DEALER  
• The assembling, the installation and the first application of the machine is under the OREC dealer’s 
responsability. 
• Read the instruction manual as well as the safety measures. Check that all the before delivery and 
at delivery check points specified in the following lists have been verified and possibly modified 
before delivering the machine to its owner. 
 

CHECKS BEFORE DELIVERY 
• Check that all the shields, grids and safety guards are in place and in a good condition. 
• Check that the hydraulic hoses are in place and in a good condition. Replace them if necessary.  
• Check that there is no oil leak, repair if necessary. 
• Check that the safety instruction stickers are in place and in a good condition. Replace them if  
necessary. 
• Check that all the bolts and screws are properly tightened with the right torque (refer to torque 
chart). 
• Protect the grease nipples by coating them with grease and lubricate the machine. 
• Check that the machine can work properly. 
 

CHECKS ON DELIVERY 

 Show the user how to perform the adjustments. 

 Explain to the user the importance of the lubrication and show him the different greasing points on 

the machine. 

 Show him the safety devices, grids, guards and the optional equipments. 

 Give the instruction manual to the customer, ask him to read it carefully. 

 

SAFETY RULES 

 

CAUTION

 

Some of the illustrations show the machine with no guard, no shield. Never use the machine 
without these devices

 

 Learn to stop the machine in case emergency.  

 Read this manual. 

 Do not let anybody use the machine before having read and understood this 

manual. 

 Do not let children use the machine. 

 Do not wear loose clothes. They might be grasped by moving parts. 

 Always wear protection equipments for when using the machine. 

 Only work during daylight or with a good artificial light. 

 Check that the safety instruction stickers are in place and in a good condition. 

 Keep the machine free from debris or mud. 

 Check that the machine can work properly before any use. 

 

Summary of Contents for HR662






























Reviews: