background image

26 

 

LIMITED WARRANTY 

 

Each new product manufactured by OREC is guaranteed under the cope of the following terms. The 

warranty applies to defective parts due to defect in assembling and construction or/and in material 

imputable to us. It is valid for a period of one year and for normal use of the machine. It does not 

apply to engines manufactured by other companies that also guarantee their materials and whose 

guarantee is supplied with the machine. 

 

1° This guarantee is limited to the sole replacement of the defective parts during one year 

commencing with the purchasing date of the machine. The guarantee is limited to the parts that are 

previously shown to and acknowledged by OREC. 

2° Each part concerned by a guarantee claim must be returned to OREC’s in order to be inspected, 

repaired or replaced. The part(s) must be returned with freight prepaid and must be accompanied with 

a proof of the purchase. The part(s) must be packed with the greatest of care to ensure their 

protection. 

3° The machine must not have been worn out, repaired or maintained by anyone without OREC’s 

previous authorization. The machine must not have been damaged in a road accident, roughly 

handled or unproperly used. 

  

This guarantee does not compell OREC or its dealer to reimburse the labour costs or the carriage 

costs to the repairer. 

 

NO OTHER GUARANTEE SHALL BE APPLIED TO THIS MACHINE EXCEPT THE LEGAL 

GUARANTEE. OREC SHALL NOT BE LIABLE FOR ANY DAMAGE OR COST INVOLVED BY THE 

MACHINE, FOR EXAMPLE : 

1. 

HIRING COSTS 

2. 

TURNOVER LOSSES 

3. 

WORK DONE BY A REPLACING MACHINE 

OREC DOES NOT TAKE ON ANY OTHER OBLIGATION AND DOES NOT AUTHORIZE ANYBODY 

TO TAKE ON ANY OTHER OBLIGATION THAN THOSE MENTIONED IN THE 3 PARAGRAPHS 

ABOVE. 

To know the name of your dealer, report to: OREC 

 

NOTES 

............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 
............................................................................................................................................................................ 

Summary of Contents for HRC663



























Reviews: