OREC RABBIT RM60W Instruction Manual Download

Page: 39 / 39

OREC RM60W

LIMITED WARRANTY

Each new product manufactured by OREC is guaranteed under the cope of the following terms. The warranty

applies to defective parts due to defect in assembling and construction or/and in material imputable to us. It is

valid for a period of one year and for normal use of the machine. It does not apply to engines manufactured by

other companies that also guarantee their materials and whose guarantee is supplied with the machine.

1° This guarantee is limited to the sole replacement of the defective parts during one year commencing with the

purchasing date of the machine. The guarantee is limited to the parts that are previously shown to and

acknowledged by OREC.

2° Each part concerned by a guarantee claim must be returned to OREC’s in order to be inspected, repaired or

replaced. The part(s) must be returned with freight prepaid and must be accompanied with a proof of the purchase.

The part(s) must be packed with the greatest of care to ensure their protection.

3° The machine must not have been worn out, repaired or maintained by anyone without OREC’s previous

authorization. The machine must not have been damaged in a road accident, roughly handled or unproperly used.

This guarantee does not compel OREC or its dealer to reimburse the labour costs or the carriage costs to the

repairer.

NO OTHER GUARANTEE SHALL BE APPLIED TO THIS MACHINE EXCEPT THE LEGAL GUARANTEE. OREC

SHALL NOT BE LIABLE FOR ANY DAMAGE OR COST INVOLVED BY THE MACHINE, FOR EXAMPLE :

HIRING COSTS

TURNOVER LOSSES

WORK DONE BY A REPLACING MACHINE

OREC DOES NOT TAKE ON ANY OTHER OBLIGATION AND DOES NOT AUTHORIZE ANYBODY TO TAKE

ON ANY OTHER OBLIGATION THAN THOSE MENTIONED IN THE 3 PARAGRAPHS ABOVE.

To know the name of your dealer, report to: OREC at : www.orec.co.jp

NOTES

...................................................................................................................................................................................

Summary of Contents for RABBIT RM60W








































Search results

Summary of Contents for RABBIT RM60W

Reviews:

Related manuals for RABBIT RM60W

Brands by name

Popular brands

OREC RABBIT RM60W, Instruction Manual

Search results

Summary of Contents for RABBIT RM60W

Reviews:

Related manuals for RABBIT RM60W

Brands by name

Popular brands