background image

11

GB

TAKING MEASUREMENTS

If you have entered a user setting, you can make use of the saved settings to automatically
find out your weight, BMI, and Body Fat Index. For users who do not have settings stored, you
can choose to take measurements as a “Guest User”.

It is necessary that you step onto the Monitor with your bare feet. The electric signal

sent from the Monitor cannot give readings if socks or shoes are worn.

TAKING BODY FAT MEASUREMENTS WITH STORED USER SETTINGS

Diagram

Instruction

1. Press user setting switch 1, 2, 3, or 4 to select

the user corresponding to your settings. The
LCD will show your height, gender and age.

2. Wait until your settings disappear and the

weight “0.0” is displayed.

3. Step on the Monitor. Stand still while the

measurement is being taken. The Monitor will
beep when the measurement is complete.
The weight, BMI, and Body Fat Index will
display.

If “ 

 ” is shown, the Monitor is unstable

while measuring your weight. Make sure to
remain still and place the Monitor on a flat
surface. Use the carpet feet if the ground is
uneven. Step off the Monitor and follow the
instructions from the beginning.

If “  

 ” is shown, you have stepped on

the Monitor too early. Step off the Monitor and
follow the instructions from the beginning.

If “   ” is shown, the maximum loading

capacity for the Monitor has been exceeded.
Step off the Monitor and try again with less
than 150kg of weight.

If you wait for too long before stepping

on the Monitor, the LCD display will go blank.
Step off the Monitor and follow the instructions
again from the beginning.

NOTE

NOTE

NOTE

NOTE

NOTE

Summary of Contents for GA101
















Reviews: