background image

18

GB

Delete all LAP memory groups

1. Press SELECT in TIMER 1 mode after it is reset to 00:00:00 to

enter the LAP memory recall mode.

2. Press and hold FUNC for 2 seconds to enter the LAP memory

delete mode.

3. Press SELECT to select deleting all LAP memories.

4. Press and hold FUNC for 2 seconds to confirm the deletion of

all the LAP memories. “donE” followed by “--” will be shown
on the display after the deletion.

5. Press FUNC to quit to TIMER 1.

Refer to Fig. 5e to delete all LAP memory groups for TIMER 1.

Notes:

a) If left idle for 30 sec, it will go back to TIMER 1.

b) To cancel the deletion of the LAP memory groups, press FUNC

to go back to the LAP memory recall mode.

TIMER 2 – 10 MIN SAILING TIMER/TIMER 3 – 6 MIN
SAILING TIMER

RA201 has  two pre-set sailing timers: TIMER 2: 10 min sailing
timer and TIMER 3: 6 min sailing timer. These sailing timers function
as a countdown timer but with countdown time fixed at 10 minutes
and 6 minutes and the timer minute can be increased or decreased
while the timer is running.

1. Press FUNC from any display mode: sail-local pressure, sail-clock,

sail-altitude and sail-temperature to access to the sailing timer.

2. Press FUNC toggle to TIMER 1, TIMER 2 or TIMER 3.

3. Press ST/SP to start or stop the timer once either TIMER 2 or

TIMER 3 is selected.

4. Press +/- to increase or decrease the full counting minute while

the timer is running.

5. Press SP to stop the timer.

6. Press and hold SET for 2 seconds to reset the TIMER to the

initial pre-set value.

Refer to Fig. 5f for TIMER 2 and TIMER 3 display mode.

Notes:

a) During count down the timer minute can be increased or

decreased to the full counting minute.

b) When reaching every full minute there will be a short double

beeping sound.

c) When countdown time reaches 5 minutes, there will be short

double beeping sound for 5 seconds.

d) When countdown time reaches the last minute, there will be

continuous beeping with 1 second on and 1 second off cycle.

e) For the last 5 seconds of the countdown there will be a

continuously beeping sound.

Timer 1 -Chronometer

Timer 2 - 10 min 

sailing timer

Timer 3 - 6 min 

sailing timer

Fig.5f

FUNC

ST/SP

SET

FUNC

FUNC

FUNC

+

-

+

-

ST/SP

SET

Fig. 5f

Summary of Contents for OUTBREAKER RA201























Reviews: