background image

9

EN

FCC STATEMENT 

This  device  complies  with  Part  15  of  the  FCC  Rules. 
Operation is subject to the following two conditions: (1) 
This  device  may  not  cause  harmful  interference,  and 
(2) This device must accept any interference received, 
including  interference  that  may  cause  undesired 
operation.

  WARNING 

  Changes  or  modifications  not  expressly 

approved by the party responsible for compliance could 
void the user’s authority to operate the equipment.

  NOTE 

    This  equipment  has  been  tested  and  found 

to  comply  with  the  limits  for  a  Class  B  digital  device, 
pursuant  to  Part  15  of  the  FCC  Rules.  These  limits 
are  designed  to  provide  reasonable  protection  against 
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio 
frequency  energy  and,  if  not  installed  and  used  in 
accordance  with  the  instructions,  may  cause  harmful 
interference  to  radio  communications.  However,  there 
is  no  guarantee  that  interference  will  not  occur  in  a 
particular  installation.  If  this  equipment  does  cause 
harmful  interference  to  radio  or  television  reception, 
which can be determined by turning the equipment off 
and  on,  the  user  is  encouraged  to  try  to  correct  the 
interference by one or more of the following measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase  the  separation  between  the  equipment 
and receiver.

• 

Connect  the  equipment  into  an  outlet  on  a 
circuit  different  from  that  to  which  the  receiver  is 

connected.

• 

Consult  the  dealer  or  an  experienced  radio  /  TV 
technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact 
for support or sales. Please visit our website at www2.
oregonscientific.com/service for all enquiries.

We

Name: 

Oregon Scientific, Inc.

Address: 

19861 SW 95

th

 Ave.,Tualatin,  

 

Oregon 97062 USA

Telephone No.: 

1-800-853-8883

declare that the product 

Product No.: 

RMR391P / RMR391PA /   

 

RMR391PU

Product Name: 

Slim Projection Clock with Indoor/ 

 

Outdoor Temperature

Manufacturer: 

IDT Technology Limited

Address: 

Block C, 9/F, Kaiser Estate, 

 

Phase 1,41 Man Yue St.,     

 

Hung Hom, Kowloon,   

 

Hong Kong

is  in  conformity  with  Part  15  of  the  FCC  Rules.   
Operation  is  subject  to  the  following  two  conditions: 
1)  This  device  may  not  cause  harmful  interference. 
2) This device must accept any interference received, 
including  interference  that  may  cause  undesired 
operation.

Summary of Contents for RMR391P










Reviews: