background image

1

 GB

CABLE FREE WEATHER

STATION

MODEL: WMR928N

USER’S MANUAL

SECTION 1 INTRODUCTION

Congratulations on your purchasing the WMR928N Cable Free
Weather Station. An all-purpose easy-to-use system, the WMR928N
lets you monitor the following weather elements:

Air temperature

Relative humidity

Barometric pressure

Wind speed and direction

Rainfall

The WMR928N is also equipped with:

RF calendar clock with daily alarm

Weather forecast within 32 to 48 km (20- to 30-mile) radius

Weather alarms

Memory for maximum and minimum readings

Simple, touch-screen operation

RS232 PC connection jack

-

 backlight

STANDARD PACKAGE

The original WMR928N comes complete with the following:

Main unit (WMR928N)

Anemometer (WGR918N)

Thermo-hygrometer (THGR918N)

Rain gauge (PCR918N)

Baro-thermo-hygrometer (BTHR918N)

12V AC adapter

The thermo-hygrometer and rain gauge are powered by solar
transmitters STR928 while the anemometer is powered by solar
transmitter STR938.

The WMR928N can support up to seven different remote instruments.
You can also connect up to three optional thermo or thermo-hygro
sensors to the system.

Optional items include:

Thermo-hygro sensor (THGR228N/THGR238N)

Thermo sensor (THR228N/THR238N)

Contact an authorized dealer for optional items.

SECTION 2 INSTALLATION

The WMR928N operates at 433MHz. No wire installation is required
among units.

The WMR928N has an effective range of 100 meters in an open area.
Position the units within the range and be sure the transmission
path is clear of interference and obstacles.

Note:The anemometer, thermo-hygrometer and rain gauge should
be installed outdoors and in locations that best measure the weather
elements the instruments are designed for. As for the baro-thermo-
hygrometer, it must be installed indoors. If you have any optional
thermo or thermo-hygro sensors, they can be installed outdoors or
indoors.

THE ANEMOMETER

The anemometer measures wind speed and direction.

To install it,

1. Place the wind cup over the thinnest shaft on the anemometer’s

T-bar.

2. Tighten the screw on the base of the wind cup.

Summary of Contents for WMR928N










Reviews: