HM-6134-15
Flexible Extension Cable
Thank you for purchasing an ORIENTAL MOTOR product.
This operating manual describes product handling procedures and
safety precautions.
• Please read it thoroughly to ensure safe operation.
• Always keep the manual where it is readily accessible.
Introduction
Only qualified personnel should work with the product.
Use the product correctly after thoroughly reading the section “Safety
precautions.”
The product described in this manual has been designed and
manufactured for use as an internal component for general industrial
equipment, and must not be used for any other purpose. Oriental
Motor Co., Ltd. is not responsible for any damage caused through
failure to observe this warning.
A flexible extension cable is a cable that is an excellent means of
extending the distance between the motor and driver.
Safety precautions
The precautions described below are intended to prevent danger or
injury to the user and other personnel through safe, correct use of the
product. Use the product only after carefully reading and fully
understanding these instructions.
Warning
Handling the product without observing the instructions that accompany
a “Warning” symbol may result in serious injury or death.
• Do not use the product in explosive or corrosive environments, in
the presence of flammable gases, locations subjected to splashing
water, or near combustibles. Doing so may result in fire, electric
shock or injury.
• Assign qualified personnel the task of installing, wiring, operating/
controlling and inspecting the product. Failure to do so may result
in fire, electric shock or injury.
• Be sure to turn off the power before installing, connecting or
inspecting this product. Failure to do so may result in electric shock.
• Do not rework or modify the cable. Do not remove the sheath of
the cable and then ground or touch the shielded wire. This may
cause electric shock or trigger the ground fault interrupt circuit.
• Do not connect or disconnect the flexible extension cable
immediately after turning off the power (i.e., within 10 s). Failure to
do so may result in electric shock.
• Do not disassemble or modify the flexible extension cable. This
may cause electric shock or injury.
Caution
Handling the product without observing the instructions that accompany
a “Caution” symbol may result in injury or property damage.
• Immediately when trouble has occurred, stop running and turn off
the driver power. Failure to do so may result in fire, electric shock
or injury.
• To dispose of the flexible extension cable, disassemble it into parts
and components as much as possible and dispose of individual
parts/components as industrial waste.
Checking the product
Check the description on the nameplate and confirm that it matches
the product you have ordered.
If there is any shortage or damage, contact the sales office from
which you purchased the product.
Connection
Also refer to the operating manual for the application product.
Insert the connector surely.
If the connector is not coupled properly, malfunction of the system or
damage to the motor or driver may result.
Precautions for use
Do not bend the connector part of the cable.
OPERATING MANUAL
• Unauthorized reproduction or copying of all or part of this Operating
Manual is prohibited.
• Oriental Motor shall not be liable whatsoever for any problems relating to
industrial property rights arising from use of any information, circuit,
equipment or device provided or referenced in this manual.
• Characteristics, specifications and dimensions are subject to
change without notice.
• While we make every effort to offer accurate information in the
manual, we welcome your input. Should you find unclear
descriptions, errors or omissions, please contact the nearest office.
•
is a registered trademark or trademark of Oriental
Motor Co., Ltd., in Japan and other countries.
Six times or m
ore
the cable di
am
ete
r
Copyright
ORIENTAL MOTOR CO., LTD. 2010
When using a flexible extension cable, keep the bending radius at six
times or more the cable diameter.
If the flexible extension cable is to be bent, keep the bend radius as
large as possible. Please do not twist or pull the cable to prevent
the risk of damage.
Printed on Recycled Paper
• Please contact your nearest Oriental Motor office for further information.
Headquarters Tokyo, Japan
Tel:(03)3835-0684 Fax:(03)3835-1890
Tel:01 47 86 97 50
Fax:01 47 82 45 16
Tel:(02)8228-0707 Fax:(02)8228-0708
Technical Support Tel:(800)468-3982
8:30
A.M.
to 5:00
P.M.
, P.S.T. (M-F)
7:30
A.M.
to 5:00
P.M.
, C.S.T. (M-F)
E-mail: techsupport@orientalmotor.com
www.orientalmotor.com
Headquarters and Düsseldorf Office Tel:0211-52067-00
Fax:0211-52067-099
Munich Office
Tel:089-3181225-00
Fax:089-3181225-25
Hamburg Office
Tel:040-76910443
Fax:040-76910445
Tel:01256-347090 Fax:01256-347099
Tel:02-93906346 Fax:02-93906348
Tel:(6745)7344 Fax:(6745)9405
KOREA
Tel:(032)822-2042~3 Fax:(032)819-8745
Tel:(03)22875778 Fax:(03)22875528
Tel:66-2-254-6113 Fax:66-2-254-6114
