background image

Opening the case 

Remove the thumb screws 
as indicated. Carefully raise 
the p

and

anel as shown (about 

30mm is enough) 

 pull 

out to remove. Reverse the 
procedure to replace.

1

2

ODD cage removal 

Remove the top fixing screw completely. 

4 fixing 

screws circled. 

it to slide 

back and be lifted out over the screw 
heads, ready for ODD installation. 

Loosen (no need to remove) the 

Keyhole shaped holes 

on the base of the cage allow 

front I/O plate

DO NOT force upwards 
as this could cause 
damage to the top panel

.

 

Optical disc drive installation 

Unclip the existing plastic drive bezel from your 
ODD. The disc tray should be ejected for this and 
usually requires some upward force to the bezel. 
Slide the optical disk drive through the front of 
the cage. Before securing the drive screws, 
check/adjust the ODD’s position in the chassis - 
it should sit as close to the front I/O plate as 
possible without the drive eject button becoming 
depressed. Secure all fixing screws and double 
check the eject button functions correctly.

ODD
cage

Optical 

disk drive

Hard drive

mount

4

Summary of Contents for S16T















Reviews: