background image

Product Information 

Models 

HH models are supplied with a double glass heat barrier option only. A screen heat barrier is not 

available for HH models.

 

 

Series 

Models 

Burner 

Certification Standard 

Gas Types 

Direct Venting 

44HH 

44HH Front 

44HH RS 

44HH LS 

44HH TS 

100 Single 

US: ANSI Z21.88-2019 

Canada: CSA 2.33-2019 

Natural Gas 

or 

Propane 

Standard 

Type: Passive Vent 

Vent Size: 5”x8” (co-axial) 

Optional 

Type: Power Vent 

Vent Size: 3”x5” (co-axial) 

 NOTES: 

  For more information on Power Venting, please refer to the Power Vent System Installation and Operation Manual. 

  Venting is not supplied by Ortal with the fireplace. The fireplace is certified to be used with, and can be obtained from, the 

vent manufacturers outlined in “General Venting Requirements” section on page 28. 

Certification 

44HH series fireplaces have been tested and approved by CSA Group for safety and efficiency for use with Natural Gas (NG) and 

Propane (LP) only, and 

NOT

 for use with solid fuels. 

CSA Group is approved by the American National Standards Institute (ANSI) as an Accredited Standards Developer.

 

Certification Standard:  

US: ANSI Z21.88 – 2019: Vented Gas Fireplace Heaters 

Canada: CSA 2.33 – 2019: Vented Gas Fireplace Heaters

 

 

Products: 

CLASS 2901 84: DOMESTIC HEATERS (GAS) Vented Fireplace: Certified to US Standard  

CLASS 2901 04: DOMESTIC HEATERS (GAS) Vented Fireplace 

The fireplaces are permitted for indoor use only. “Indoor” is defined as a conditioned space. The fireplaces are not approved for 

outdoor  or partial outdoor installation.  The fireplaces must be installed while maintaining required clearances. Installation is 

recommended in living spaces such as bedrooms, living rooms, great rooms, etc. The fireplaces are not approved for closet 

installation. The fireplace must be installed according to Ortal requirements in addition to any local codes that may apply, such as 

USA: ANSI Z223.1/NFPA 54, Canada: CSA B149. 

 IMPORTANT: 

  Consult the authority having jurisdiction to determine the need for a permit prior to starting the installation. 

  It is the responsibility of the fireplace dealer and installer to ensure that this fireplace is installed and framed in compliance 

with these instructions and all applicable codes. 

  Before starting, take careful note of 

ALL

 the 

WARNINGS

 in this manual. 

 

 

Summary of Contents for 44HH Corner LS






















































Reviews: