29
Burner and Burner Inspection
Burner comes complete with all the necessary parts assembled, including: venturi,
nozzle, pilot, thermocouple and spark plug. Parts are pre-set for the specific gas type
(natural/propane) and no field adjustments are necessary.
During installation the burner and its accessories must be inspected for cleanliness and
completeness. Do NOT disassemble the components.
Instructions for changing the fuel source from natural gas to propane and nozzle details
are located in the maintenance section of the manual. This can only be performed by
technicians with a specific authorization to change these components. Actual change
must be done by the authorized technician. Not all installers are authorized to provide
gas conversion services.
Glass Panels
5mm ceramic glass front and side panels. Contact Ortal USA for replacement
parts if required.
Handling the Glass
The glass must ONLY be removed by an authorized qualified installer. The technician
should ONLY remove the glass with the glass vacuum holders supplied by the
manufacturer. Lower the glass to rest in the special wooden/polyurethane support
provided, and fit the second support to the upper edge of the glass. This is to prevent
damage to the glass edges.
When glass is installed, on a two or three sided model (corner type fireplace), for
purpose of sealing, a bead of special high temperature transparent silicon (initially
supplied by ORTAL) must be used. To apply the silicone:
Place the silicon 1/8” thick on the edge of one glass.
Then, install the other glass with the edge flush against the silicone.
Let the silicon dry and cure for 24 hours per the manufacturer’s recommendation
(Appendix D)
Summary of Contents for Clear 150 LS
