background image

General 

 

Safety Information and Warnings  

 WARNING: REVIEW ALL WARNINGS 

Be sure to review all safety warnings and installation guidelines contained in this manual and the applicable Ortal fireplace installation 

manual. Before installing Heat Control System, read and understand all instructions. Consider installation location, venting pathway, 

clearances, structural requirements, framing and finish materials, and local codes. ALL warnings and instructions apply to all products 

manufactured and distributed by Ortal. 

 WARNING: FOR USE WITH ORTAL-MANUFACTURED FIREPLACES ONLY 

The Heat Control System is authorized for use with Ortal manufactured fireplaces only. Do not attempt to use with a different 

manufacturer’s product. 

 WARNING: ELECTRICAL GROUNDING 

All electrical connections must be properly installed, insulated, and secured to avoid potential 

ELECTRICAL SHOCK 

and 

FIRE 

HAZARD

 and malfunction of the system. Consult local building code requirements. In the absence of local codes, refer to the National 

Electric Code, ANSI/NFPA 70, or the Canadian Electric Code, CSA C22.1. 

 WARNING: MATERIAL USAGE 

All materials and objects used to carry out the installation must be certified/approved or specified by Ortal and are suitable for use. 

Do NOT install the system with different materials or objects than those approved for installation by Ortal.  

 WARNING: INSTALLATION AND SERVICE 

Installation and repairs on the fireplace, Heat Control System, and vent system must be done by an Ortal-authorized qualified installer 

service agency or gas supplier. If these components are not installed by an Ortal-authorized dealer/installer, the warranty of all 

components will be void and Ortal will not be responsible for any damage caused by improper installation. The fireplace should be 

inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive 

lint from carpeting, bedding material, etc. Control compartments, burners and circulating air passageways of the fireplace must be 

kept clean. Any alteration to the product can cause soot or carbon to form and may result in damage. This damage and any other 

damage that results from not following the instructions outlined in this manual is not the responsibility of Ortal. 

 WARNING: HEAT BARRIER 

A barrier designed to reduce the risk of burns from hot viewing glass is provided with this fireplace and shall be installed. The fireplace 

MUST not be used without the heat barrier in place. If the barrier becomes damaged, the barrier shall be replaced with the 

manufacturer’s barrier for this fireplace. 

Any safety screen, guard, or barrier removed for servicing the fireplace must be 

replaced before operating. 

 WARNING: FIREPLACE TEMPERATURE 

Due to hot temperatures, the fireplace should be located out of traffic and away from furniture and draperies.  

Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing 

ignition. Clothing or other flammable material should not be placed on or near the fireplace. 

Young children should be carefully 

supervised when they are  in the same room as the fireplace

. Toddlers, young children, and others may be susceptible to 

accidental contact burns. A physical barrier is recommended if there are at-risk individuals in the house. To restrict access to a 

fireplace or stove, install an adjustable safety gate to keep toddlers, young children, and other at-risk individuals out of the room and 

away from hot surfaces. 

 WARNING: GLASS HANDLING 

Only an Ortal certified installer is authorized to remove the glass using a suction cup supplied by Ortal. 

 WARNING: INSTALLATION AND OPERATION 

The fireplace and accompanying components must be installed as an OEM installation in manufactured homes (USA only) or an 

aftermarket permanently located, or a mobile home, where not prohibited by local codes.  The fireplace must be installed in 

accordance with the Manufacturer's instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 

3280, in the United States, or the Standard for Installation in Mobile Homes, CAN/CSA Z240 MH Series, in Canada. 

Exceeding the 

restrictions imposed in these instructions may result in a fire or explosion, causing property damage, personal injury, or 

loss of life. Ortal will not be responsible for any damage caused by improper installation. Do not store or use gasoline or 

other flammable vapors and liquids near this fireplace. 

 WARNING: LOCAL CODES 

Local codes and building requirements take precedence over all requirements stated in this manual. Consult the local authority having 

jurisdiction to ensure all local codes and requirements are followed. 

 

 

Summary of Contents for Heat Control System





















Reviews: