background image

25 

 

 

 

Supplemental Information  

 

SCA Waterjet Cleaning System Limited Warranty 

 

Product 

Limited Warranty Period 

SCA Waterjet Cleaning System 

1 year 

All  new  SCA  Waterjet  Cleaning  Systems  are warranted  exclusively  by 

Oryx  Additive

,  Inc.’s

 

(“Manufacturer”) limited warranty as follows:

 

Each SCA Waterjet Cleaning System 

(“System”) and its components (“Components”), except 

those listed below under limits and exclusions, is warranted against defects in the materials 

and workmanship for a period of one (1) year from the date of installation at the end user’s 
(“Customer”)

 facility. 

Repair or replacement only: manufacturer's liability under this agreement shall be limited to 
repairing or replacing, at the discretion of manufacturer, parts, or components sufficient to 
return the system to conform to the marketing specifications of the system. 

Components  subject  to  wear  during  normal  use  and  over  time  such  as  paint,  finish,  light 
bulbs, seals, etc., are excluded from this warranty. 

This  warranty  is  void  if  the  system  is  subjected  to  mishandling,  misuse,  neglect,  accident, 
improper installation, improper maintenance, or improper operation or application, or if the 
machine was improperly repaired or serviced by the customer. This warranty is void if the 
system is not installed by a certified distributor and the proper installation documentation 
provided by the manufacturer has not been submitted. 

Liability,  whether  based  on  warranty,  negligence  or  other  cause,  arising  out  of  and/or 
incidental to sale, use or operation of the system, or any part thereof, shall not in any case 
exceed  the  cost  of  repair  or  replacement  of  the  defective  equipment,  and  such  repair  or 
replacement  shall  be  the  exclusive  remedy  of  the  purchaser,  and  in  no  case  will 
manufacturer  be  responsible  for  any  and/or  all  consequential  or  incidental  damages 
including  without  limitation,  and/or  all  consequential  damages  arising  out  of  commercial 
losses. 

This warranty is transferrable from the original end user to another party if the machine is 
sold via private sale before the end of the warranty period. 

The  foregoing  is  a  limited  warranty  and  it  is  the  only  warranty  by  manufacturer. 
MANUFACTURER  DISCLAIMS  ALL  OTHER  WARRANTIES,  EXPRESS  OR  IMPLIED,  INCLUDING 
BUT  NOT  LIMITED  TO  ALL  WARRANTIES  OF  MERCHANTABILITY  AND  FITNESS  FOR  A 
PARTICULAR PURPOSE. 

 

 

Summary of Contents for SCA Waterjet



























Reviews: