2
3
SAFETY INSTRUCTIONS
CONTENTS
OPERATING
MAINTENANCE
Osaki Power Tools are committed to the Production of Quality Power Tools
that are designed for high performance and long service life.
If safety and maintenance procedures are observed they will last for many years.
Man, Earth and the Universe
are forces that create an
immovable centre of balance . . .
the
balance of power
“
”
GENERAL SAFETY
Keep work area clean - clutter invites
injuries.
Do not expose power tools to rain or
damp conditions. Do not use power tools
near flammable liquids or gases.
Do not let people who are not familiar
with power tools handle them without
supervision. Keep children away from the
work area.
Store tool in dry, secure place, away
from children.
Use correct tool for the job, do not force
small tools or attachments to do the job
of a heavy tool. The job will be done
more efficiently and safely if the tool is
used for the intended application.
Wear safety glasses or a dust mask if
necessary.
Secure work with a clamp or vice. This
will allow both hands free to operate the
tool.
Before using tool ensure that all parts
are functional. A damaged part should be
repaired and serviced by an authorised
technician.
Stay alert at all times. Watch what you
are doing and use your common sense.
Do not operate tools when you are tired.
Do not overreach. Keep a proper footing
and balance at all times.
Do not force the tool. It will do the job
better and safer at the rate for which it
was intended.
Do not attempt to use the tool whilst it is
connected to the charger.
Do not carry the charger by its cord.
Do not use the charger if it is cracked,
h a s b e e n d r o p p e d o r t h e c o r d i s
damaged in any way .
Do not charge battery below 4
°
C (40
°
F)
or above 40
°
C (104
°
F).
Do not attempt to open the screwdriver
or battery charger for any reason.
Do not store the screwdriver in locations
where the temperature may reach or
exceed 40
°
C (104
°
F).
Guard against electric shock. Prevent
body contact with grounded surfaces; for
example, pipes and radiators.
If you drive through a “live” wire do not
touch any metal part of the tool until
a f t e r i s o l a t i n g t h e p o w e r a n d f u l l
withdrawal.
Do not alter the tool or the charger.
Model Number
CS36TR
Nominal Voltage
230v~50 Hz
Battery
3.6V
Torque
45 Kgf-cm
No Load Speed
200 rpm
Gross Weight
1.58kg
Screwdriver Weight Only
603gm
1 x SOCKET ADAPTOR
1/4
” x 50mm
9 x SOCKETS
4, 5, 6, 7, 8, 9, 10, 11, & 12mm
Plus holder.
5 x HSS DRILL BITS
1/4
” - 1.5, 2, 3, 4, 5.5mm
Fitted with
1/4
” Hex drive bits.
1 x SCREWDRIVER
3.6V Cordless
1 x CHARGER
3 hour
1 x CARRY CASE
Fitted to hold all accessories.
1 x BIT HOLDER
1/4
” x 60mm
20 x
1/4
” HEX DRIVER BITS
CROSSPOINT HEAD 1, 2 & 3
POZIDRIV
®
1, 2 & 3
SLOTTED 3, 4 & 5mm
HEX 2, 2.5, 3, 4, 5, 6mm
TORX
®
T10, T15, T20, T25 & T30
Plus 2 holders.
Before drilling in ceilings and walls check for concealed electric wires and gas/water pipes using a
metal detector. Keep long hair away from drill. Do not operate while wearing loose clothing.
FORWARD/REVERSE SWITCH OPERATION
Press on the left side of the switch to remove fasteners with a
counterclockwise rotation. (See Fig. a)
Press on the right side of switch to drive/install fasteners with a
clockwise rotation. (See Fig. a)
LOCKING THE SCREWDRIVER
The Osaki Cordless Screwdriver is fitted with an automatic
spindle lock which engages when the motor is not active,
to allow it to be used as a manual screwdriver.
TORQUE ADJUSTMENT COLLAR
The screwdriver has 12 torque positions. To change settings,
turn the torque adjustment collar to the left from setting 1 to increase the
torque and back towards the right to decrease the level of torque. When
the optimum torque position for a particular application is not known it
is recommended to start at a low position and “work up” until the right
setting is achieved. This will avoid unnecessary damage of the workpiece.
(See Fig. b) Do not attempt to force the collar past the number 12 torque
position.
TURNING ON THE LIGHT
To turn the light on, rotate the light switch collar to the right until the bottom
triangle aligns with the light symbol. (See Fig. c)
The exterior plastic parts of the screwdriver may be cleaned with a damp cloth and a mild detergent.
The charger should only be cleaned using a dry cloth or a soft non-metallic brush. Do not use water or
detergent.
WARNING:
Disconnect the charger from the mains power supply outlet before cleaning.
Fig. a
Fig. b
Fig. c
OSA-279-6340K_Instructions.qxd 25/06/2008 09:13 Page 2
