background image

Brand new system

Unused for more 

than 5 days

Filters over 6 months old

Usage Problems

Likely Cause

Suggested Solution

Water level in the Supply 

Pitcher is too low.

Air blocked in the water 

system.

Filters are blocked and 

need replacement. 

Abnormal sound during 

the filtering. 

Remove any water in the 

Supply Pitcher and refill 

to the 5 litre level and try 

again.

Open and close the lid of 

source water tank several 

times to try to flush air 

from the system.

Change to the RO 

Membrane Filter first and 

if this does not solve the 

problem then a do a 

complete filter change. If 

the system was run in 

this state permanent 

damage can be made to 

the pump.

Water leakage.

Drip Tray is full of water.

Foreign matter stuck in 

the one way valve of the 

Supply Pitcher base.

Foreign matter stuck on 

the seal spacer of the 

Supply Pitcher.

Internal water leakage.

Empty the tray.

Clean the one way valve

Clean the seal spacer

Power off and empty the 

Supply Pitcher and con-

tact customer service.

Odour in the 

water

Dispense 5 litres of water 

before using the system.

Dispense 5 litres of water 

before using the system.

Change all the filters

Summary of Contents for Zero IP-II




















Reviews: