8
Extension and flexion stop kits are available separately for order.
To install a kit:
1. Remove the condyle pads from the medial and lateral hinges. Remove
retaining screws.
2. Using a short Philips head screwdriver, slide the 0° stop out of the
hinge on both sides.
3. Re-apply the desired extension stop and gently secure it with the
retaining screw.
4. Repeat steps to change the flexion stop.
NOTE:
Do not overtighten retaining screw.
PCL Strap Attachment
(optional accessory, not included):
The PCL kit is designed to counteract posterior subluxation of the tibia.
Trim and adjust the PCL strap for proper fit.
Attaching PCL Strap – Acculign version
1. Note height position on medial and lateral hinge arms.
2. Remove hook-and-loop fastener to access connection area.
3. Remove Acculign hinge screws.
4. Remove Acculign hinge d-Ring.
5. Position PCL Acculign hinge d-ring.
6. Position PCL Acculign hinge inserts with raised portion into recessed
pocket.
7. Return frame to initial positions on hinge arms.
8. Tighten Acculign screws.
9. Reapply hook-and-loop fastener.
10. Attach PCL strap.
Attaching PCL Strap – other versions
1. Take the end of the PCL strap with the alligator clip and loop it
through the PCL slot on the brace frame. Alligator clip will close on
the inside of the strap. Trim strap if necessary
(Figure 12)
.
2. Loop the other end of the PCL strap through the frame. Fasten strap
and secure it onto the outside of the strap
(Figure 13)
.
3. Place the adjustable pad in the middle of the strap. Trim the strap pad
if needed.
4. Fully extend the leg. Tighten the strap, securing the pad.
PRODUCT CARE
Follow the steps below to keep your brace in a good condition. Liners,
straps and pads can be removed for cleaning. Hand-wash using mild
non-detergent soap. Rinse thoroughly, Air-dry.
If the brace moves, clean lower liners and pads with an alcohol wipe or
damp cloth.
NOTES:
• Do not machine wash
• Do not tumble dry
Hinge Maintenance
Regularly check the hinge regularly for dirt, debris or similar
contamination. Remove dirt, debris or similar contamination carefully
using water or compress air.
Summary of Contents for REBOUND DUAL ST
