background image

Page 2

Warning

The operating description in this Instruction Manual is for use by qualified personnel only. To
avoid electrical shock, do not perform any servicing of this unit other than that contained in the
operating instructions, unless you are qualified and certified to do so by Omnitron Systems
Technology, Inc.

Caution

All user-required operations can be performed without opening the unit. Never attempt to open
or remove the cover or tamper with the unit. There are no user replaceable or serviceable parts
in this unit. Equipment is not intended to be installed and used in a place (home, school, or public
area) accessible to the general population.

Warranty

This product is warranted to the original purchaser against defects in material and workmanship
for a period of TWO YEARS from the date of shipment. A LIFETIME warranty may be obtained by
the original purchaser by REGISTERING this product with Omnitron within 90 days from the date
of shipment. TO REGISTER, COMPLETE AND MAIL OR FAX THE ENCLOSED REGISTRATION
FORM. Or you may register your product on the Internet at www.omnitron-systems.com. During
the warranty period, Omnitron will, at its option, repair or replace a product which is proven to
be defective.

For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s
expense. Omnitron will pay the shipping charge to return the product to Buyer’s designated US
address using Omnitron’s standard shipping method.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate use
and/or maintenance of the equipment by Buyer, Buyer-supplied equipment, Buyer-supplied
interfacing, unauthorized modifications or tampering with equipment (including removal of equipment
cover by personnel not specifically authorized and certified by Omnitron), or misuse, or operating
outside the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation or maintenance.

No other warranty is expressed or implied. Omnitron specifically disclaims the implied warranties
of merchantability and fitness for any particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not
be liable for any direct, indirect, special, incidental, or consequential damages, whether based
on contract, tort, or any legal theory.

Summary of Contents for iConverter 8090-0













Reviews: