background image

Page 12

General Note: Be careful with tent windows in cold weather, as creasing or crushing them will cause
breakage.

Caution: Use adequate ventilation. Portable heaters use up oxygen

Caution: Use adequate ventilation. Portable heaters use up oxygen

Caution: Use adequate ventilation. Portable heaters use up oxygen

Caution: Use adequate ventilation. Portable heaters use up oxygen

Caution: Use adequate ventilation. Portable heaters use up oxygen
and emit carbon monoxide. Use reflectors and identifying lights after

and emit carbon monoxide. Use reflectors and identifying lights after

and emit carbon monoxide. Use reflectors and identifying lights after

and emit carbon monoxide. Use reflectors and identifying lights after

and emit carbon monoxide. Use reflectors and identifying lights after
dark or during limited visibility

dark or during limited visibility

dark or during limited visibility

dark or during limited visibility

dark or during limited visibility.....

To Collapse Tent and Transport:

1. Remove support bars and store inside the sled.
2. Retract main frame bars by pressing in button while

sliding the bar farther into the tube.

3. Fold the tent in towards the sled so all the bars are

laying on top of the sled.

4. Tuck in excess tent material.
5. Ready for transport.
6. Reverse to set up the fishhouse again.

Fold tent inward
towards sled.

21. On the front of the fishhouse, start in the corners and work inward, snap the plastic trim seal on the canvas tent

(Item 2) to the 

lip

 edge of the sled (Item 1). The tent (Item 2) will meet in the middle and should be free to open

and close so it can be removed. Ref. Diagram 13.

Diagram 13

Start here and
work inward

Back

Left Side

Front

Right Side

Start Here and
work inward

2

1

Velcro attaches
at this point

Trim seal

Self-tapping screw

Detail A

21

Left Side

Back

1

Line up seam
on the corner

NOTE: Check for proper fit of canvas

before installing screws in trim lock.

Summary of Contents for Pro XT Cabin














Reviews: