8) Using the torque wrench, tighten the cap screw (for definitive mounting:
5 Nm
- see Fig. 6).
5.2 Mounting in the Modular Prosthesis
CAUTION
Improper assembly of the screw connections
Fall due to breakage or loosening of the screw connections
►
Clean the threads before every installation.
►
Apply the installation torques provided.
►
Observe the instructions for securing the screw connections and the
use of the correct length.
Mounting
>
Recommended tools and materials:
710D4 Torque Wrench, 636K13 Loctite®
1)
For definitive mounting:
Use Loctite® to secure the set screws (see Fig. 4, Item 1).
2) Turn in the set screws.
3)
For trial fitting:
Use the torque wrench to tighten the set screws (
10 Nm
).
For definitive mounting:
Pre-tighten the set screws with the torque wrench (
10 Nm
) and then
tighten (
15 Nm
- see Fig. 6).
4) Use suitable set screws to replace any set screws that extend out too far
or screw in too deeply (see selection table).
Selection Table for Set Screws
Reference number
Length (mm)
506G3=M8x12-V
12
506G3=M8x14
14
506G3=M8x16
16
Adjustment
The 4 set screws can be used to make static adjustments at any time during
alignment, trial fittings, and even after the prosthesis is finished.
16 | Ottobock
Summary of Contents for 2R30
