20
5.1 Setting the 476L52=SK010/15/20/25 Multi Axis Assemblies
The clamping lever (Fig. 8, Item A) of the rotation joint (Fig. 8, Item B) must
be loosened. This clamping lever can be replaced by the provided screw
(see section 7), if encroachment makes the setting difficult.
- The headrest is set in the desired position.
- Tightening the clamping lever (Fig 8, Item A) enables you to fix it in the
desired position.
- The clamping process consists of two stages:
. First the ball clamping is clamped in the lower area of the shaped part
(Fig. 8, Item B).
2. Then the upper adjustment bar is clamped in place by more tightening.
5.2 Setting the 476L52=SK030/35 Gooseneck
- The clamping lever (Fig. 8a, Item A and B) of the assemblies must be
loosened. These clamping levers can be replaced by the provided screws
(see section 7, 50S7=8x6), if encroachment makes the setting diffi-
cult.
- The headrest can then be set in the desired position.
- Tightening both the clamping levers (Fig 8, Item A) enables you to fix it in
the desired position.
6. Setting to the needs of the user
476L52=SK010/15/20/25 Multi Axis Assemblies
Select the settings according to the needs of the user.
- Loosen the clamping lever (Fig. 5, Item B) on the vertical adjustment bar
in order to change the height.
- To adjust the horizontal setting, loosen the clamping lever (Fig. 8, Item
A) on the shaped part (Fig. 8, Item B) and slide the adjustment bar for-
ward or backward. The 476L52=SK00/ 5 Assemblies offer additional
possibilities for the horizontal settings by letting it be offset to the front or
back.
- Set the extension stop so that it lies on top of the clamping plate (Fig. 3
and 4) and tighten the Allen head screws.
- Once you have completed all the desired settings, you must tighten all
the screws.
647G353_CS 2_neu.indd 20
07.08.2007 12:18:59 Uhr
Summary of Contents for 476L52-SK010
