Service work
490E75=0_C
Ottobock | 37
8) Loosen and remove the setscrew with square nut under the arm support and remove the holder from the arm
support (see Fig. 59, item 1).
9) Attach the rear cover (see Page 19).
Installing the push-button module
1) If necessary: Seal the holder with a ribbed plug (see Fig. 60, item 1).
2) If necessary: Join the 2 parts of the holder using a screw and nut (see Fig. 61, item 1).
3) Align the 2 parts of the holder and secure them with the setscrew (see Fig. 62, item 1).
4) Slide the holder into the arm support and secure it with the setscrew and square nut under the arm support (see
Fig. 59, item 1).
INFORMATION: Attach the holder on the arm support opposite the control panel.
5) Attach the push-button module to the holder with the magnet (see Fig. 58, item 1).
6) Apply the symbols according to the assignment (see Fig. 58, item 2).
7) Remove the rear cover (see Page 19).
8) Connect the 24 V connection to the internal charging connection (OBC) of the controller (see Fig. 57, item 1).
9) Connect the 24 V connection to the terminal box (see Fig. 56, item 1).
10) Connect the 12 V and signal lines to the terminal box (see Fig. 55, item 1).
11) Attach the terminal box to the bottom of the seat plate using a hook-and-loop fastener (see Fig. 54).
JII@>OOC@NO@M@JE<>FOJOC@J?@>JII@>ODJIJIOC@>JIOMJGK<I@GN@@DB{ÂÀxDO@H¾{@>PM@OC@
><=G@NRDOCOC@><=G@<OO<>CH@IONDI?JDIBNJN@@DB{ÂÀxDO@H¿{
12) Optional: In combination with a chin control, also connect an actuator switch (493T75=SK076) to the terminal
box (see Fig. 63, item 1).
13) Attach the rear cover (see Page 19).
14) If necessary: Program the push-button module.
INFORMATION: After installing the push-button module, the parameter set has to be adapted. The
KMJBM<HHDIB JA OC@ KPNC}=POOJI HJ?PG@ >C<IBDIB OC@ <NNDBIH@IO ><I JIGT =@ <?<KO@? =T <P-
OCJMDN@?x LP<GDu@? K@MNJII@G{ JM APMOC@M DIAJMH<ODJIx KG@<N@ >JIO<>O TJPM I<ODJI<G OOJ=J>F O@<H{
53
54
55
56
Summary of Contents for 490E75 Series
