Service work
490E75=0_C
40 | Ottobock
z@K@I?DIBJIOC@>JIuBPM<ODJIxOC@M@H<T<GM@<?T=@<NPDO<=G@HJ?PG@><MMD@MJIOC@
back support. In this case, attach the connection module to the existing module carrier and continue
RDOCNO@KÄ{
5) IN@MOOC@ORJN>M@RN<I?IPON=@OR@@IOC@M@O<DIDIBKG<O@<I?PKK@M>JII@>ODIBOP=@<I?uMHGTODBCO@IOC@HOJ
10 Nm (see Fig. 72, item 2).
6) IN@MOOC@ORJN>M@RN=@OR@@IOC@>JII@>ODJIHJ?PG@<I?HJ?PG@><MMD@Mx<I?uMHGTODBCO@IOC@HN@@DB{ÄÀx
item 1).
7) Insert the two screws and nuts between the retaining plate and module carrier, and tighten them slightly (see
Fig. 71, item 1).
INFORMATION: Set the module carrier onto the retaining plate as far to the outside as possible.
8) Put the clamp around the back tube (see Fig. 70, item 2).
9) IN@MOOC@N>M@R<I?IPO=@OR@@IOC@HJ?PG@><MMD@M<I?>G<HKx<I?uMHGTODBCO@IDOOJ1 Nm (see Fig. 70, item 1).
10) Firmly tighten all module carrier screws.
11) Install the cable along the holder, arm support holder and seat frame. Secure the cable with the cable attach-
ments as you do so (see Fig. 69, item 1).
INFORMATION: Make sure that cables cannot get stretched, pinched or caught when the wheelchair
is operated. For moving parts in particular, check whether all movements are possible without putting
strain on the cables or causing them to stick out. Do not route cables over sharp edges.
12) Thread the cable through the module carrier and connect it to the connection module (see Fig. 68).
13) Connect the connection module to the bus system (see Fig. 67). Secure the cable with cable attachments as
you do so.
zJII@>OOC@<IBG@?@I?JAOC@><=G@OJOC@>JII@>ODJIHJ?PG@{<DIO<DINPAu>D@IO?D-
stance to adjacent components and actuators. The connection module is connected to the seat module
JMOC@>JIOMJGG@M?@K@I?DIBJIOC@>JIuBPM<ODJI{
14) If necessary: Connect additional special controls to the connection module.
15) Put on the cover of the module carrier (see Fig. 66).
16) Press in and engage the four locking pins on both sides of the cover (see Fig. 66, item 1).
66
67
68
69
Summary of Contents for 490E75 Series
