Service work
490E75=0_C
Ottobock | 43
INFORMATION: On-board programming is not activated on delivery of the control device. In this case,
first carry out PC programming, back up the parameters and activate on-board programming when
needed.
3) @G@>OOC@ÞTNO@HÞH@IPRDOCOC@PK?JRI<MMJRN<I?>JIuMHTJPMN@G@>ODJIRDOCOC@MDBCO<MMJR{
4) @G@>OOC@ÞJTNOD>F><GD=M<ODJIÞH@IPRDOCOC@PK?JRI<MMJRN<I?>JIuMHTJPMN@G@>ODJIRDOCOC@MDBCO<MMJR{
5) Follow the instructions on the display module.
zPMOC@MDIAJMH<ODJIM@B<M?DIBOC@><GD=M<ODJI><I=@AJPI?DIOC@žÆÀÂPN@MH<IP<G
from the control device manufacturer.
6) The display module shows when the calibration has been completed successfully. The display then returns to the
system menu.
INFORMATION: If you have activated on-board programming, deactivate it again using PC program-
ming and back up the parameters.
4.8.14 Replacing the mo-Vis joystick control on the arm support
INFORMATION
To make them easier to see, the black joystick control components are shown in silver in the illustrations that follow.
f
Prerequisites:
Switch off the control device and deactivate the main fuse (see Page 15).
f
Tools: Allen wrench, sizes 4, 5
Removing the mo-Vis joystick control on the arm support
1) INFORMATION: Note the installed position of the cables and cable attachments. The mo-Vis controller
is mounted under the seat or in the module carrier on the back support by default.
Disconnect the cable of the mo-Vis controller from the cable extension (not illustrated). Remove the cable attach-
ments if necessary.
2) Loosen and remove the screw and square nut under the arm support and remove the holder from the arm support
(see Fig. 79, item 1).
3) If necessary: Remove the individual components of the joystick control. Loosen the respective clamping screws
to do so (see Fig. 80, item 1).
4) Remove the joystick with the mo-Vis controller.
Installing the mo-Vis joystick control on the arm support
1) Slide the holder into the arm support and secure it with the screw and square nut under the arm support (see
Fig. 79, item 1).
2) NN@H=G@ OC@ DI?DQD?P<G EJTNOD>F >JIOMJG >JHKJI@IONx <GDBI OC@H <I? uMHGT ODBCO@I OC@ M@NK@>ODQ@ >G<HKDIB
screws (see Fig. 80, item 1).
zGDBIOC@EJTNOD>F<>>JM?DIBOJOC@<MMJRJIOC@=JOOJHN@@DB{žxDO@H¾{C@<MMJR
has to point forward in the direction of travel.
3) Attach the mo-Vis controller according to the original installed position.
4) Position and connect the cables according to their original installed position. Reattach the loosened cable at-
tachments as you do so.
INFORMATION: Make sure that cables cannot get stretched, pinched or caught when the wheelchair
is operated. For moving parts in particular, check whether all movements are possible without putting
strain on the cables or causing them to stick out. Do not route cables over sharp edges.
5) Verify that the joystick is securely positioned.
6) If necessary: Recalibrate the joystick.
Summary of Contents for 490E75 Series
