background image

22

   

 

Figure 33 

 

 

 

 

 

Figure 34

Now close the transit lock latch (Figure 33).

Put the HUBFIX bath lift in an appropriate place (Figure 34).

First let the bath lift drip dry. If needed dry it off before placing it in an appropriate storage area as illustrated.

16 Maintenance, cleaning and care

Your HUBFIX bath lift has the CE seal of approval. This indicates that the manufacturer has determined that this 

complete medical product meets the requirements of the EU 93/42/EWG standard.

The correct function of the bath lift should be checked before every use.

If you discover any problems, please contact your Otto Bock approved dealer to have them fixed. We also 

recommend that you have the device serviced every twelve months by your Otto Bock approved dealer.

After every bath, use clean water and a shower attachment to wash down the HUBFIX bath lift and remove any 

traces of soap or other body-care substances.

Regularly clean all parts of the frame and plastic components with regular mild household cleaner.

The suction cups and rubber feet must be clean and free of grease or soap to insure the best grip with the 

bottom of the tub.

If they are worn (and offer insufficient grip) please change them immediately.

17 Guarantee terms & conditions

The Otto Bock Warranty applies only when the product is used according to the specified conditions and for the 

intended purposes, following all manufacturer's recommendations (please also see our general terms of sale, 

supply and payment).

18 Technical information

Measurements (centimeters) and weight (kilograms) 
Overall length   

 

99 cm  - 122 cm

Overall width   

 

41 cm  -  71 cm

Minimum height when folded 

10 cm

Maximum height 

 

41 cm

Maximum load   

 

30 kg

Total weight 

 

 

121⁄2 kg

647G154_GB_inhalt

13.02.2004, 11:20 Uhr

22

Summary of Contents for Hubfix II














Reviews: