background image

3 Safety

3.1 Explanation of warning symbols

WARNING

Warning regarding possible serious risks of accident or injury.

CAUTION

Warning regarding possible risks of accident or injury.

NOTICE

Warning regarding possible technical damage.

3.2 General safety instructions

WARNING

Lack of instruction

Tipping over, falling of the user due to lack of knowledge

Instruct the user or the attendant in the proper use of the product when handing it over.

CAUTION

Use of unsuitable tools

Pinching, crushing or damaging the product due to use of unsuitable tools 

When  completing  the  tasks,  only  use  tools  that  are  suitable  for  the  conditions  at  the  place  of  work  and  for
which safety and the protection of health are assured with proper use.

Observe the specifications in the section "Required Tools".

NOTICE

Tipping or falling of the product

Damage to product due to lack of attachment

When you work on the product, secure it so that it cannot tip over or fall over.

Use a clamping fixture to secure the product whenever you work on it at a workbench.

NOTICE

Use of unsuitable packaging

Damage to the product caused by transportation using incorrect packaging

Use only the original packaging for delivery of the product.

3.3 Safety Instructions for Assembly

WARNING

Changed diameter/installation position of the wheels

Tipping, falling over of the user due to blocked wheels

Modification of the size and position of the front wheels and of the drive wheel size can lead to wobbling of the
front wheels at higher speeds. If changes are required, verify the horizontal alignment of the wheelchair frame
(see the section "Adjusting the drive wheels", "Adjusting the caster wheels"). 

WARNING

Incorrect installation of the anti-tipper/missing anti-tipper

Tipping  over,  falling  of  the  user  due  to  failure  to  observe  the  installation  instructions  and  because  of  incorrect
adjustment

Depending upon the settings of the chassis, the centre of gravity, the back angle and the experience of the
user, the use of an anti-tipper may be necessary.

For a small wheelbase and a backrest that is tilted far back, an anti-tipper may need to be installed on both
sides, depending upon the user's experience. 

Verify  that  the  anti-tipper  has  been  installed  and  adjusted  properly.  Find  the  appropriate  position  with  the
assistance of a helper.

6

Safety

Start M4 XXL, Start M6 Junior

Summary of Contents for Start M4 XXL

































Reviews: