OUMAN EH-203
OUMAN EH-203
OUMAN EH-203
OUMAN EH-203
Press the
button to move cursor to "Clock functions”. Press
OK.
Clock functions; relay control
Clock functions
Time/ Date
H1 drop program
H2 drop program
R1 time program
R2 Control
HW temp.incr.
Press the
button to move cursor to indicate the relay control (R1 or
R2) whose controls you want to access. Press
OK.
0:00 Relay1ON
_ _ _ _ _
_ _
0:00 RelayOFF
_ _ _ _ _ _ _
H1 Select
Heating curve
Settings
Measurements
Info water temp
DH Energy meas.
Control modes
Clock functions
Type info
Press
ESC
until the display no longer changes.
You are then in the "Selection" display shown in the adjoining picture.
OPERATING INSTRUCTION:
Press
OK.
KV
Ulkol. °C
Menovesi °C
Valinta
Automaattiohj
L2
Ulkol. °C
Menovesi °C
Valinta
Automaattiohj
KV
Ulkol. °C
Menovesi °C
Valinta
Automaattiohj
L2
Ulkol. °C
Menovesi °C
Valinta
Automaattiohj
KV
Ulkol. °C
Menovesi °C
Valinta
Automaattiohj
L2
Automaattioh
j
HW
Automatic
H2
Automatic
Relays can control many different functions, e.g., sauna stoves,
locking doors etc. Relay clock functions are taken into use and
labeled according to use in the relay control mode. (see p. 26 and 27).
Then the relay can be controlled using a GSM, if a GSM-modem has been
installed into the regulator (optional equipment).
H1
Outdoor
°C
SupplyTemp
°C
Selection
Automatic
-15
52
R2 Control
Time program
Contin ON
Contin OFF
Timer ON
m
Timer OFF
m
0
0
The relay can be used to switch an electric apparatus on and off at desired
times. When the time program is in the "ON” mode the relay is activated. In this
mode the time (time and weekday) is set for the relay to be activated and the
time (time and weekday ) is set for the relay to be inactivated. Time
programming is done in the same way as L1 drop program time programming
(see prev. p.). The regulator can be programmed for a maximum of 7 program
series (on/off series) per relay.
The relay's time program is not in use. The relay is in a forced ON mode (=
relay is activated).
The relay is in a forced Off mode (= relay is inactivated).
The relay's time program is temporarily replaced by a timer. The relay is in the
ON mode (= activated) for a set time (range 0…999min), after which the relay
switches to a time programmed mode. Press the or + button to change the time
on the timer. The amount of time left on the timer appears on the display.
The relay's time program is temporarily replaced by a timer. The relay is in the
OFF mode (= is inactivated) for a set time (range 0…999min), after which the
relay switches to a time programmed mode. Press the or + button to change
the time on the timer. The amount of time left on the timer appears on the
display.
Time program:
Continuous ON:
Continuous OFF
Timer ON
Timer OFF
RELA
Y1:
(T
ime
program/
ON/OFF/
Timer
ON
min/
Timern
OFF=
min)
59
*
59
RELA
YS
KEYWORD:
Relays
If the relay reserved for time control has been labeled,
R1 (R2) it will indicate what the relay is reserved for
(e.g., sauna, outside doors)
Set the time for the relay to be activated and the days
of the week for the relay to be activated.
In addition, set the time for the relay to be inactivated
and the days of the week for the relay to be inactivated.
Press the
or
button and confirm the time on the timer by pressing
.
-
+
OK
15
