background image

2

www.outdoorrooms.com

HGI-31 : 1-23-2018

• Important operating and maintenance 

instructions included.

• Read, understand, and follow these 

instructions for safe installation and operation.

INSTALLER: Leave manual with the appliance.
CONSUMER: Retain this manual for future   

 

   

 

reference.

• 

Do not store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance.

• 

WHAT TO DO IF YOU SMELL GAS

  - Do not try to light any appliance.
  - Do not touch any electrical switch;  
    do not use any phone in the building.
  - Leave the building immediately.
  - Immediately call your gas supplier  
    from a neighbor’s phone. Follow the  
    gas supplier’s instructions.
  - If you cannot reach your gas  

 

     supplier, call the fire department.

• 

Installation and service must be 
performed by a qualified installer, 
service agency, or the gas supplier.

DO NOT DISCARD THIS MANUAL!

WARNING:

WARNING

WARNING

It is imperative the burner be kept clean. 

The appliance must be serviced and 

maintained to ensure proper operations and 

performace. All service should be done by 

NFI certified persons.

INSTALLATION AND SERVICE OF THIS 

APPLIANCE SHOULD BE PERFORMED BY 

AUTHORIZED PERSONNEL. 

FOR USE IN WOOD BURNING FIREPLACES

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could 

result in serious injury, death or property damage.

Summary of Contents for HGI-31
































Reviews: