background image

9

HGI-31 : 1-23-2018

www.outdoorrooms.com

5

Gas Hookup and Information

FIRE RISK

FIRE RISK

CHECK FOR GAS LEAKS

EXPLOSION RISK:

 VERIFY INLET PRESSURES

EXPLOSION RISK

EXPLOSION RISK

FIRE RISK

ASPHYXIATION RISK

WARNING

WARNING

WARNING

• High pressure may cause over-fire 

condition.

• Low pressure may cause explosion
• Verify minimum pressures when other 
household appliances are operating

Install regulator upstream of valve if line pressure 
is greater than 10.5 in WC for natural gas and 14 
in WC for LP gas.

• Gas build-up during line purge may 
ignite

• Purge should be performed by authorized 
technician
• Ensure adequate ventilation
• Ensure there are no ignition sources such as 
sparks or open flames

• Check all fittings and connections

• Do not use open flame
• After the gas line installation is complete, all 
connections must be tightened and checked 
for leaks with a commercially available leak-
check solution. Be sure to rinse off all leak-
check solution following testing.

Fittings and connections may have loosened 

during shipping and handling.

Before making gas connections, ensure the 

appliance being installed is compatible with the 

available gas type.

NOTE: Have the gas supply installed in accordance 

with local building codes, if any. Installation should 

be done by an authorized installer approved and/

or licensed as required by the locality.

Incoming gas line should be piped to the 

12.7mm (1/2 inch) connection on the manual 

shut-off valve.

A small amount of air will be in the gas 

supply lines. When first lighting appliance it 

will take a short time for air to purge from 

lines. Subsequent lighting of the appliance 

will not require such purging.

Proper input pressures are required for optimum 

performance and safety. Gas line sizing 

requirements need to be made following NFPA-

54.

Pressure requirements for appliance are shown 

in table below. Minimum pressures must be 

met when other household gas appliances are 

operating. 

A. FUEL

C. GAS CONNECTION

B. GAS PRESSURE

PRESSURE

NATURAL GAS

PROPANE

Min. inlet pressure

5 inch WC

10.5 inch WC

10.5 inch WC

14 inch WC

Max. inlet pressure

Summary of Contents for HGI-31
































Reviews: