background image

12 

 

 

 

 
 
 

 

 

 

 

Care and maintenance note:  

Light scratches may be removed from the poly-wood surfaces of this 

fire pit by gently sanding with 220-grit sandpaper in the same 

direction as the grain. Sanding too deeply or not following the grain 

of the material could result in permanent damage. 

 

IMPORTANT 

Please consult your Crystal Fire Plus instruction manual for detailed 
instructions and important information related to the burner 
installation including: lighting and operating instructions, safety 
information, and proper tightening of connections with two wrenches.  

DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE PLUS BURNER WITHOUT 
FIRST CONSULTING THE CRYSTAL FIRE PLUS OWNER’S MANUAL. 

 

WARNING 

After consulting the manual and following instructions, remember; before 

operating, all gas connections must be fully checked for leaks 

Warranty: Fire pit tables are covered under a 1- year 

manufacturer’s warranty. Please visit 

https://www.outdoorrooms.com/product-registration 

to register your product.

 

 

14400 Southcross Drive West 

•  Suite 100 •  Burnsville, MN  55306 

Toll Free: 1-866-303-4028 

 

Sales@OutdoorRooms.com

 

 

 

Summary of Contents for KW-1242-K













Reviews: