Outlaw Audio
12
Before you set the crossover frequency using your receiver
or processor, make sure it is connected to the Ultra-X12’s
SUB IN EXTERNAL X-OVER jack. Then refer to your receiver
or processor’s instructions for adjusting the subwoofer
crossover frequency.
¼
To set the crossover frequency with your receiver
or processor’s crossover control :
Set your receiver or processor’s subwoofer
crossover to the frequency recommended by the
manufacturer of your speaker.
OR
1.
Determine the lowest frequency your main speakers
can reproduce, by following the steps outlined on
page 11, under "Adjusting the Crossover Frequency.
2.
Set the Ultra’s INTERNAL X-OVER FREQUENCY con-
trol 10Hz above your speaker’s lowest frequency.
If you hear distortion coming from any of your speaker’s,
raise that speaker’s crossover point. Adjust the crossover for
the center, front left, and front right to a lower setting, if
you hear voices coming from the subwoofer.
Setting the Ultra-X12 Crossover control
Set the subwoofer crossover frequency
Set the subwoofer crossover frequency
Setting the crossover with your
receiver or processor
Setting the Phase switch
Before you set the crossover frequency control using the
Ultra-X12, make sure your receiver or processor is con-
nected to the Ultra-X12’s SUB IN INTERNAL X-OVER jacks or
HIGH LEVEL INPUTS FROM AMPLIFIER terminals.
¼
To set the crossover frequency with the Ultra-X12’s
INTERNAL X-OVER FREQUENCY control :
Set the Ultra’s INTERNAL X-OVER FREQUENCY
control to the frequency recommended by the
manufacturer of your speaker.
OR
1.
Determine the lowest frequency your main speakers
can reproduce, by following the steps outlined on
page 11, under "Adjusting the Crossover Frequency.
2.
Set the Ultra’s INTERNAL X-OVER FREQUENCY con-
trol 10Hz above your speaker’s lowest frequency.
Adjust the control lower if you hear voices coming from the
subwoofer.
Phase Switch
Depending upon the phase of your speakers, including the
subwoofer, in relation to the listening position, the bass
response may be smoother if you reverse the phase of the
Ultra. Try both positions of the phase switch to determine
which way sounds more bass-heavy.
The bass-heavier position is the setting where the output
of the Ultra and the main speakers are most in phase. Use
program materials with bass in the crossover region such
as music containing bass drums, double basses, bass guitar,
etc., to determine the correct setting.
Use only with a 250v fuse
Employer uniquement avec
un fusible de 250v
RIGHT
LEFT
120V - 60HZ
5A
T 5A L 250V
MODEL Ultra-X12
POWERED SUBWOOFER
CAUTION
AVIS: RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
PASS-THRU TO
LOUDSPEAKERS
RIGHT
LEFT
HIGH LEVEL INPUTS
FROM AMPLIFIER
(INTERNAL X-OVER)
POWER
POWER
PHASE
VOLUME
THRU
INTERNAL
X-OVER
FREQUENCY
(HZ)
SUB IN
INTERNAL
X-OVER
0°
180°
OFF
AUTO
ON
MIN MAX
60
120
PORT
MODE
MAX OUTPUT
MAX EXTENSION
L
R
SUB IN
EXTERNAL
X-OVER
ON
AC
FUSE
OFF
MASTER POWER
CAUTION
FOR CONTINUED
PROTECTION AGAINST
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE
FUSE AND RATING
Use only with a 250v fuse
Employer uniquement avec
un fusible de 250v
RIGHT
LEFT
120V - 60HZ
5A
T 5A L 250V
MODEL Ultra-X12
POWERED SUBWOOFER
CAUTION
AVIS: RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
PASS-THRU TO
LOUDSPEAKERS
RIGHT
LEFT
HIGH LEVEL INPUTS
FROM AMPLIFIER
(INTERNAL X-OVER)
POWER
POWER
PHASE
VOLUME
THRU
INTERNAL
X-OVER
FREQUENCY
(HZ)
SUB IN
INTERNAL
X-OVER
0°
180°
OFF
AUTO
ON
MIN MAX
60
120
PORT
MODE
MAX OUTPUT
MAX EXTENSION
L
R
SUB IN
EXTERNAL
X-OVER
ON
AC
FUSE
OFF
MASTER POWER
CAUTION
FOR CONTINUED
PROTECTION AGAINST
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE
FUSE AND RATING
SRC
PWR
ON
Setup
Mute
OK
Func
+
+
VOL
CH
–
–
VOL
CH
Exit
Menu
Surr Mode
AM/FM
MEM
Spkr Set
Test
Direct
T. Mode
Auto PST
Demo
LFE T
rim
CH Delay
CH Level
Video
Game
Aux
TV
Status
Ext
Tone
Disc
Menu
PIP
Swap
Input
RPT
Last
CC
Sleep
Info
FAV
Guide
VOD
Night
Sync
CBL
SAT
DISC
TV
AUX
AUD
STB
TNR
1
2
3
4
5
6
7
8
9
0
OFF
PHASE
0°
180°
PHASE
0°
180°
PHASE
0°
180°
PHASE
0°
180°
Adjusting the Crossover Frequency
(cont’d)
Determine
the speaker
manufacturer’s
recommended
subwoofer
crossover
frequency
Determine
the speaker
manufacturer’s
recommended
subwoofer
crossover
frequency
Set the INTERNAL X-OVER
FREQUENCY control to the
speaker manufacturer’s
recommended subwoofer
crossover frequency
Set your receiver or processor’s
crossover to the speaker
manufacturer’s recommended
subwoofer crossover frequency
Set the INTERNAL X-OVER
FREQUENCY control 10Hz
above your speaker’s
lowest frequency
Set your receiver or processor’s
crossover to 10Hz above your
speaker’s lowest frequency
PHASE control
Using program material with bass content in the crossover
frequency region, set the PHASE control to the positon that
yields the bass-heavier sound
Determine
the lowest
frequency
your speaker
can cleanly
reproduce
Determine
the lowest
frequency
your speaker
can cleanly
reproduce
