background image

 Shut off the valve at the gas cylinder or the regulator before moving the appliance.
 Use only the type of gas specified by the manufacturer.
 Repairs should be done by a qualified person.
 In case of violent wind, particular attention must be taken against tilting of the 

appliance.

 To check that the regulator seal is correctly fitted and able to fulfil its function.
 To close the gas supply at the valve of the gas cylinder or the regulator after use.
 Do not use this appliance until all connections have been leak tested.
 In the event of gas leakage, the appliance shall not be used or if alight, the gas 

supply shall be shut off and the
appliance shall be investigated and rectified before it is used again.

 Checking the tubing or the flexible hose per month and each time the cylinder is 

changed.

 The tubing or the flexible hose must be changed within one year.
 The hose assembly must be replaced prior to the appliance being put into operation if 

there is evidence of
excessive abrasion or wear, or if the hose is damaged, and that the replacement hose 
assembly shall be that
specified by the manufacturer.

 The heater should be inspected before use and at least annually by a qualified 

service person. More frequent
cleaning may be required as necessary. It is imperative that control compartment, 
burners and circulating air
passageways of the appliance be kept clean.

 Shut off and check heater immediately if any of the following conditions exist:
 The smell of gas in conjunction with extreme yellow tipping of the burner flames.
 Heater does not reach a proper temperature. A temperature less than 5 will cause 

restricted 

 heat flow and

the appliance will not work properly.

 The appliance starts making popping noises during use (a slight popping noise is 

normal when the appliance
is extinguished).

 The regulator & hose assembly must be located out of pathways where people may 

trip over it or in area where
the hose will not be subject to accidental damage.

 Any guard or other protective device removed for servicing the heater must be 

replaced before operating the
heater.

 Children and adults should be warned of the hazards of high surface temperatures 

and should stay away to avoid
burns or clothing ignition.

 Young children and pets should be carefully supervised when they are in the area of 

the heater.

 Clothing or other flammable materials should not be hung from the appliance, or 

placed on or near the appliance.

 Certain material or items when stored under or near this appliance will be subjected 

to radiant heat and could be
seriously damaged.

 Do not place articles on or against this appliance.
 Do not use or store flammable materials near this appliance.
 Do not spray aerosols in the vicinity of this appliance while it is in operation.
 Always maintain at least 915mm clearance from combustible materials.
 Always position the appliance on a firm level surface.
 The appliance shall only be installed or operated with maximum height from the rim 

of reflector to the ground, so
the adjustable device shall be fixed according to this requirement.’

 The use of this appliance in enclosed areas can be dangerous and is PROHIBITED.

Summary of Contents for 842-186














Reviews: