Outsunny 845-489V90, Assembly & Instruction Manual

NOTE

: It is dangerous to use the machine without the hopper. 

How do I use this product?

Before  using  the  machine,  read  the  instructions  thoroughly  and  acquaint  yourself 
with the features of the machine.
Before  inspecting  or  servicing  any  part  of  the  appliance,  switch  off,  pull  the  plug 
from the mains and make sure that all moving parts have come to a complete stop.
1.  Inspect  the  material  to  be  shredded  before  starting.  Remove  any  objects  or 

debris  that  could  be  thrown,  jammed  or  become  entangled  in  the  blades. 
Remove  any  soil  from  root  balls.  Foreign  bodies  like  stones,  glass,  metals, 
fabrics,  or  plastics  must  not  enter  the  in-feed  chute,  these  could  damage  the 
blades.

2.  Always  place  the  machine  on  firm  level  ground.  During  operation,  do  not  tilt  or 

move.

3.  Allow the cutting blades to reach full speed before feeding the material into the 

in-feed chute.

4.  Use the machine to shred the following materials only:

Twigs and branches (Max. diameter 40mm)
Waste from pruning bushes
Waste from trimming hedges
Plant material and other garden waste
Leaves and plant roots (remove soil from roots before shredding)

5.  Do  not  fill  soft  waste  such  as  kitchen  rubbish  into  the  shredder,  but  compost 

them.

6.  Feed the material to be shredded into the corner of the in-feed chute, if it is not 

too bulky, the material will be drawn in by the blades.

7.  Only insert as much material so that the in-feed chute will not be blocked up.

8.  Warning

:  Long  material  extending  out  from  the  machine  could  lash  out  when 

being drawn in by the blades. Please keep at safe distance.

9.  Ensure the shredded material can fall freely from the discharge chute.
10. 

To make finer compost the shredded material can be shredded for a second 

time.

11. Do  not  allow  the  shredded  material  to  build  up  to  a  level  where  it  blocks  the 

discharge chute. If the material builds up too far it could reach the cutting blades 
and be thrown out of the in-feed chute.

12. 

Organic material contains a large amount of water and sap that can stick to 

the shredder. To avoid this the material should be left for a few days to dry out. 
Large branches however are best shredded when they are fresh.

13. 

If  during  cutting  the  blade  stalls,  stop  the  shredder  immediately  and 

disconnect it from the mains supply before investigating the cause.

14. 

Remove  any  jammed  debris  from  the  blades  and  examine  them  for  any 

damage before re-commencing shredding.

15. 

If  the  blade  has  stalled  for  more  than  5  seconds  the  safety  overload  switch 

will  operate  and  switch  the  machine  off. Allow  the  machine  to  cool  down  for  at 
least  1  minute  before  re-starting.  Push  the  overload  switch  first  and  then  push 
on the On/Off switch to re-start the machine.

16. 

If the cutting mechanism strikes any foreign object or if the appliance should 

start making any unusual noise or vibration, immediately switch off and allow the 
cutting means to stop. Pull the plug from the mains supply and take the following 
steps:

i) 

Inspect for damage.

ii) 

Replace or repair any damage parts.

iii) 

Check for and tighten any loose parts.

EN