background image

4

WARNING

!

Motorized Doors are large, heavy objects that move with the help of springs under high tension and electric 

motors. Since moving objects, springs under tension, and electric motors can cause injury, your safety and the 

safety of others depend on you reading the information in this manual. If you have any questions or do not 

understand the information presented, call your nearest factory service representative. 

In this manual the words Danger, Warning, and Caution are used to stress important safety information. The word:

DANGER

 indicates an imminently hazardous situation which, if not avoided, will result in death or serious 

injury.

WARNING

 indicates a potentially hazardous situation which, if not avoided, could result in death or serious 

injury.

CAUTION

 indicates potentially hazardous situation which, if not avoided, may result in injury or property 

damage.

The word 

NOTE

,

 is used to indicate important steps to be followed or important considerations.

!

!

!

IMPORTANT

READ PRIOR TO ANY DOOR OPERATION

1.  Read manual and warnings carefully.
2.  Keep the door in good working condition. Periodically lubricate all moving parts of door.
3.  If door has a sensing edge, check operations monthly. Make any necessary repairs to keep it functional.
4.  AT LEAST twice a year, manually operate the door by disconnecting it from the operator. The Door 

should open and close freely. If it does not, the door must be taken out of service and a trained service 
representative must correct the condition causing the malfunction.

5.  The Operator Motor is protected against overheating by an internal thermal protector. If the motor 

protector is tripped, a trained service technician may be needed to correct the condition which caused the 
overheating. When the motor has cooled, thermal protector will automatically reset and normal operation 
can be resumed.

6.  In case of power failure, the door can be operated manually by pulling the release cable to disconnect the 

operator drive system.

7.  Keep instructions in a prominent location near the pushbutton.

POTENTIAL HAZARD

EFFECT

PREVENTION

MOVING DOOR

WARNING

Could result in Serious 

Injury of Death

Do Not operate unless the doorway is in sight and free of 

obstructions. Keep people clear of opening while door is 

moving. 

Do Not allow children to play with the door operator.

Do Not change operator control to momentary contact unless 

and external reversing means is installed.

Do Not operate a door that jambs or one that has a broken 

spring.

ELECTRICAL SHOCK

WARNING

Could cause Serious 

Injury or Death

Turn off electrical power before removing operator cover.

When replacing the cover, make sure wires are not pinched or 

near moving parts.

Operator must be electrically grounded.

HIGH SPRING TENSION

WARNING

Could cause Serious 

Injury or Death

Do Not try to remove, repair or adjust springs or anything to 

which door spring parts are fastened, such as wood block, steel 

bracket, cable or any other structure or like item.

Repairs and adjustments must be made by trained service 

representative using proper tools and instructions.

!

!

!

SAFETY INFORMATION

Summary of Contents for COUNTDOWN TIMER





















Reviews: