background image

 

 

 

ALL RIGHTS RESERVED 

 

 

 

These instructions apply to the following models: 
TYPHON 2000 MEC.LS and TYPHON 2000 MAG-LS. 
The automatism TYPHON 2000KG gear motor S is an 
electro-mechanical operator  designed for moving sliding 
gates. 

 

The 

non-reversing 

reduction 

system 

ensures 

the 

mechanical  locking  of  the  gate  when  the  gear  motor  is  not 
operating, therefore it is not necessary to install any electric 
lock 

 

A convenient manual release with customised key makes it 
possible  to  move  the  gate  in  case  of  a  power  failure  or 
operator malfunction. 

 

The TYPHON 2000  gear motor was designed and built for 
controlling vehicle access. 

AVOID ANY OTHER USE. 

 
 
 

 

1. DESCRIPTION 

AND 

TECHNICAL 

SPECIFICATIONS 

 
1.1. DIMENSIONS TYPHON 2000KG 

 
 
 
 
 
 
 
 

 

mm. 335

 

 
 
 
 
 

 

mm. 

 

290 

. 210

 mm 

 
 
 
 

 

1.2. MAXIMUM USE CURVE 

 

The curve makes it possible to establish the maximum 
working  time (T) according to the use frequency (F). With 
reference to IEC 34-1 Standard, the TYPHON 2000 KG 
gearmotor can operate with a use frequency of 40%. 

 

To  ensure  efficient  operation,  it  is  necessary  to  operate  in 
the work range below the curve. 

 

Important: 

The curve is obtained at a temperature of 20°C.

 

Exposure to the direct sun rays can reduce the use 
frequency by up to 20%. 

 

Calculation of the use frequency 
 

Use  frequency  is  the  percentage  of  the  effective  working 
time (o closing) compared to the total time of cycle 
(o c pause times). 
Calculation formula: 

 

                        

Ta + Tc 

         %F =          __________________

       

X 100 

                    
                   

Ta + Tc + Tp + Ti 

 

 

where: 

 

Ta = opening time 

 

Tc = closing time 

 

Tp = pause time 

 

Ti = time of interval between two complete cycles 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

1.3. TECHNICAL SPECIFICATIONS 

 

MODEL 

1000 

 

TYPHON 2000 

 

 

 

 

 

 

Power supply 

230V (+6% -10%) 50Hz 

Absorbed power (W) 

550 

 

650 

 

RPM (X min.) 

 

1400 

 

Absorbed current (A) 

1,7 

 

2,4 

 

Capacitor 

16 uf 

 

25 uf 

Reduction Ratio 

 

1 : 30 

 

Pinion 

Modulo 4 - Z16 

Thrust on pinion (daN) 

80 

 

150 

 

Winding thermal protection 

150°C 

 

130°C 

Use frequency 

40% 

 

Intensive use 

Oil quantity (Lt) 

0,250 

 

 

Oil type 

Total Equivis HZS 68 

Operating temperature 

-20°C +55°C 

Gearmotor weight (Kg) 

16 

 

17 

 

Protection class 

 

IP 55 

Gate max weight (Kg) 

1000 

 

2000 

 

Gate speed 

9,6 ml/min. 

         Clutch 

               No 

(electronic clutch is 

recommended) 

 

 

Double disc 

In oil 

 

                               

 

 

MOTOR TYPHON 2000 

Summary of Contents for TYPHON 2000










Reviews: