background image

Satellite settings / DiSEqC: on / off

Satellites are changed using the receiver‘s DiSEqC signals. The signals or the
DiSEqC ID of the receiver must comply with the ID list saved in the control unit of 
your Vision system.
16 satellites with a DiSEqC ID number are preset in your Vision system 
(see table).
The DiSEqC function is active when the DiSEqC option has been enabled or if 
„DiSEqC“ is set to On with the Vision III control unit being on!

No.  Satellite name

DiSEqC ID

1

Astra 1     

19.2° East

1

2

Astra 2     

28.2° East

5

3

Astra 3     

23.5° East

3

4

HotBird     

13.0° East

2

5

Eutelsat 5 West

5.0° West

6

Thor/Intel 10-02

1.0° West

7

7

Astra 4     

5.0° East

6

8

Eutelsat 16

16.0° East

15 

9

Eutelsat 7

7.0° East

 9

10

Amos  2/3

4.0° West

13

11

Hispasat    

30.0° West

21

12

Telstar 12   

15.0° West

17

13

Eutelsat 9   

9.0° East

18 

14

Eutelsat 33   

33.0° East

24

15

Hellas Sat 2  

39.0° East

10

16

Türksat 2/3     

42.0° East

11

Here you can adopt the default settings of the Vision system into your satellite 
receiver. Please refer to the manual of your receiver.

Important:

Further DiSEqC functions (DiSEqC V3-ID, DiSEqC Rec-ID, DiSEqC Data) are only 
accessible if „DiSEqC: on/off“ is set to „

on

“ !

19

Summary of Contents for Oyster Vision III
























Reviews: