background image

WT181416

ASSEMBLY INSTRUCTIONS

Verify Package Contents and Assemble Poles

Tent : 1 each

1) Assemble the roof frame as shown below matching color coded poles to color coded connectors. Use the diagram below and the replacement 
     parts listing on page 4 as reference. Make certain the metal springs lock into place on all the connectors.
2) Attach ridge roof and eave poles:
     (A) Blue/green ridge and eave poles, positioning blue section over front of the tent.
     (B) Red roof poles.
3) Attach hooks along ridge and eaves to frame.

2) Assemble steel poles by inserting the 
     tapered ends into the adjacent sections.

1) Verify package contents as listed below

Steel poles : 21 each (total)
( ) denotes color coding

Rainfly : 1 each

IMPORTANT NOTES:

* Assemble your tent before camping to become    
   familiar with the assembly.
* Two people are recommended for setup.
* Select a clean, level area for the campsite free                      
   of debris and sharp objects, away from a  

 

   natural watercourse.
* Use of a ground cloth is recommended to
   prolong the life of the tent floor and provide
   additional insulation and moisture protection.
* To prevent damage to the zippers, unzip the
   doors and windows of the tent prior to 
   disassembly allowing air to move freely.
* Seam seal the inside stitched seams of the tent.
   This will improve weather resistance. Available 
   in sporting goods departments. Discoloration
   may occur if applied to outside seams.

Hanging Shelf : 2 each

Tent Stakes : 24 each

Color Coded Conectors:
9 each (pre-attached) 

(A) Ridge & eave (Blue/green) -3 each

(B) Leg - 6 each

Step 2: Assemble Roof Frame

Step 1: Spread and Stake Tent

1) Spread out the tent floor side down on a 
     flat, clean and level area.
2) Stake down the tent by inserting a stake 
     through the stake loops, located at the
     corners of the tent.
3) Hammer the stakes into the ground at a 45

0

     angle using a hammer or mallet.
4) Make certain the tent floor is pulled out 
     evenly and tightly.

Media pocket : 1 each

WT181416     8/17

(D) Closet leg - 4 each

(E) Closet Roof - 2 each

(C) Roof (red) - 6 each
        

C

A

C

C

A

Green

Blue

A

C

C

C

C

C

C

A

A

Summary of Contents for WT181416

Page 1: ...nd other hazards which may cause harm to this product or its occupants Have a minimum of two adults for assembly During assembly poles are under tension If not held firmly in place during assembly poles could break or flip up possibly causing serious injury Safety glasses may be worn throughout the assembly process as an additional precaution Excercise care when using electric devices in and near ...

Page 2: ...ts away from a natural watercourse Use of a ground cloth is recommended to prolong the life of the tent floor and provide additional insulation and moisture protection To prevent damage to the zippers unzip the doors and windows of the tent prior to disassembly allowing air to move freely Seam seal the inside stitched seams of the tent This will improve weather resistance Available in sporting goo...

Page 3: ...takes together in bags provided 3 Lay pole bag at opposite end from door Tightly roll bag skin and fly forcing air through unzipped door 4 Secure with ties and place in carry bag with stakes and accessories 5 Tent must be clean and dry before storage Store off concrete floor Be certain campfires are extinguished Dispose of trash appropriately Dimension A should be close to but not exceed the lengt...

Page 4: ... this occurs avoid touching walls to reduce contact leakage Leaving the doors and windows open will reduce moisture condensation Store wet clothing outside of tent Not applicable to screen houses A ground cloth under the floor helps prolong its life provides additional insulation and moisture protection The cloth should be smaller than the floor to prevent rain from running under the tent Not appl...

Reviews: