3
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Using the extension cord retaining hook
The cord retaining hook is used to “anchor” an extension cord when it is
connected to the power lead of the tool. It prevents the extension cord
from being accidentally disconnected from the blower’s power cable or
shaken loose during use. It should be used at all times.
1. Make a loop in the end of the
extension lead and pass the loop
though the hole in the rear of the
handle.
2. Hook the loop over the cord
retaining hook. Pull the extension
cord to secure it in position over the
cord retaining hook.
3. Connect the extension
lead to the power cord.
Route the power and
extension cord away
from the work area to
prevent contact with the
blower.
Note:
Always use an approved extension lead suitable for the power
input of this tool.
Blowing
The blower can be used to clean
corners, fences, walls or beneath
cars.
Hold the blower firmly, turn the
trigger switch on, point the jet of air
in front of you and move forward
slowly. Move the blower from
side to side, with the tube several
inches above the ground.
Be careful where you point the jet
of air as it can move heavy material
and cause injury or damage to
bystanders.
Note.
Be aware of other people
and animals in the area where you
are to be operating the blower.
Note.
Avoid collisions with hard objects which could damage your
machine.
Turning ON
To turn the blower on, depress
the trigger switch.
Turning OFF
To turn the blower off, release
the trigger switch.
Connecting the blow tube and direction nozzle
1. Unpack the blow tube and
direction nozzle.
2. Connect larger end of the direction
nozzle to the smaller end of the
blow tube.
3. Ensure that all 3 buttons on the blow tube
sit within the holes in the direction nozzle.
4. Connect the blow tube to the
blower housing, ensuring that the
blower housing tabs click into the
holes in the blow tube.
5. Secure the blower tube to the
blower housing with the two 12mm
screws.
1. Direction nozzle
2. Blow tube
3. Handle
4. On/Off trigger
5. Cord retaining hook
6. Air intake vent
7. Assembly screws 2 x 12mm
ELECTRIC BLOWER (BLW-1800)
KNOW YOUR PRODUCT
LMBLGTK-000
1. ASSEMBLY
3. USING THE BLOWER
2. TRIGGER SWITCH
4. GENERAL MAINTENANCE
SETUP & PREPARATION
OPERATION
MAINTENANCE
1
2
7
3 4
6
5
WARNING!
ALWAYS ENSURE ThE BLOWER IS
DISCONNECTED FROM ThE POWER SUPPLY
DURING ASSEMBLY AND/OR MAINTENANCE.
WARNING!
DO NOT USE ThE BLOWER WITh ANY
TYPE OF ACCESSORY OR ATTAChMENT. SUCh
USAGE MIGhT BE hAZARDOUS.
• Keep air intake clean and air vents free of debris to avoid overheating
the motor.
• Do not use cleaning agents to clean the plastic parts of the tool.
A mild detergent on a damp cloth is recommended. Water must never
come into contact with the tool.
• If the blower vibrates abnormally, stop motor immediately. Abnormal
vibration usually indicates a mechanical problem continued operation
could lead to injury or damage.
• No lubrication is necessary as the motor is equipped with lifetime-
lubricated bearings.
Note:
Ozito Industries will not be responsible for any damage or injuries
caused by the repair of the tool by an unauthorised person or by
mishandling of the tool.
WARNING:
BEFORE CLEANING YOUR BLOWER OR
CARRYING OUT ANY MAINTENANCE PROCEDURE,
MAKE SURE ThAT ThE MOTOR IS OFF AND ThE BLOWER
IS DISCONNECTED FROM ThE POWER SUPPLY TO
PREVENT ACCIDENTAL STARTING.
WARNING!
DO NOT SWITCh ThE MAChINE ON
IN ENCLOSED OR POORLY VENTILATED SPACES
OR IN ThE PRESENCE OF FLAMMABLE AND/OR
ExPLOSIVE LIqUIDS, GASES AND POWDERS.
WARNING!
TO REDUCE ThE RISK OF ELECTRIC
ShOCK, ThE USE OF A RESIDUAL CURRENT
DEVICE RATED AT 30mA OR LESS IS RECOMMENDED.